# Task: IPv6 Neighbor Discovery — v8.2.0

**Version:** 8.2.0
**Category:** Basic discovery
**Description:** IPv6 Neighbor Discovery
**New in this version:** No
**IPv6 Support:** Yes
**URL:** https://matrix.ipfabric.io/8.2.0/task/200142570

---

## Vendor Support Matrix

| Vendor / Family | Status | IPv6 | Notes | Transport |
|-----------------|--------|------|-------|-----------|
| aws | ✗ | ✗ |  | — |
| alcatel@aos | ✗ | ✗ |  | — |
| avocent@acs | ✗ | ✗ |  | — |
| azure | ✗ | ✗ |  | — |
| brocade@fastiron | ✗ | ✗ |  | — |
| cisco@ios | ✓ | ✓ |  | CLI |
| cisco@ios-xe | ✓ | ✓ |  | CLI |
| cisco@nx-os | ✓ | ✓ |  | CLI |
| cisco@ios-xr | ✓ | ✓ |  | CLI |
| cisco@asa | ✓ | ✓ |  | CLI |
| cisco@wlc-air | ✗ | ✗ |  | — |
| cisco@sg | ✗ | ✗ |  | — |
| cisco@ftd | ✗ | ✗ |  | — |
| cisco@aci | ✓ | ✓ |  | CLI |
| cisco@meraki | ✗ | ✗ |  | — |
| cisco@viptela | ✗ | ✗ |  | — |
| cisco@apic | ✗ | ✗ |  | — |
| cisco@encs | ✗ | ✗ |  | — |
| dell@ftos | ✗ | ✗ |  | — |
| dell@powerconnect | ✗ | ✗ |  | — |
| dell@os10 | ✗ | ✗ |  | — |
| dlink@dgs1210 | ✓ | ✓ |  | CLI |
| dlink@dgs1250 | ✓ | ✓ |  | CLI |
| dlink@des3000 | ✓ | ✓ | IPv6 neighbor discovery supported on DES-3200 only; DES-3028 has no IPv6 | CLI |
| fs@fsos | ✗ | ✗ |  | — |
| gcp | ○ | ○ |  | — |
| hpe@comware | ✗ | ✗ |  | — |
| hpe@aruba | ✓ | ✓ | API: Aruba New Central; only neighbours on a VLAN SVI the gateway VLAN endpoint reports with an IPv4 address - the endpoint exposes no IPv6, so an IPv6-only SVI, a routed port and a loopback are all dropped | CLI ✗, API |
| hpe@arubasw | ✗ | ✗ | API: the ND cache names the physical port, which no API source resolves to an SVI | — |
| hpe@arubacx | ✓ | ✓ | API: Aruba New Central; only neighbours on an interface l3Interfaces emits: VLAN SVIs from the switch VLAN endpoint plus every addressed interface in `show running-config` | CLI ✗, API |
| hpe@3com | ✗ | ✗ |  | — |
| hpe@aruba-iap | ✗ | ✗ | API: no IPv6 neighbor command | — |
| riverbed@steelhead | ✗ | ✗ |  | — |
| fortinet@fortigate | ✓ | ✓ |  | CLI |
| fortinet@fortiswitch | ✓ | ✓ |  | CLI |
| forcepoint@ngfw | ✓ | ✓ |  | CLI |
| paloalto@pan-os | ✓ | ✓ |  | CLI |
| paloalto@prisma | ✗ | ✗ |  | — |
| juniper@junos | ✗ | ✗ |  | — |
| juniper@mist | ✗ | ✗ |  | — |
| checkpoint@gaia | ✗ | ✗ |  | — |
| checkpoint@gaia-embedded | ✗ | ✗ |  | — |
| extreme@boss | ✗ | ✗ |  | — |
| extreme@enterasys | ✗ | ✗ |  | — |
| extreme@voss | ✗ | ✗ |  | — |
| extreme@exos | ✗ | ✗ |  | — |
| arista@eos | ✓ | ✓ |  | CLI |
| f5@big-ip | ✗ | ✗ |  | — |
| f5@f5osa | ○ | ○ |  | — |
| f5@f5osc | ○ | ○ |  | — |
| huawei@vrp | ✗ | ✗ |  | — |
| mikrotik@routeros | ✗ | ✗ |  | — |
| quagga | ✗ | ✗ |  | — |
| frr | ✗ | ✗ |  | — |
| versa@vos | ✗ | ✗ |  | — |
| silverpeak@unity | ✗ | ✗ |  | — |
| vmware@nsx-t | ✗ | ✗ |  | — |
| vmware@velocloud | ✗ | ✗ |  | — |
| ruckus@vsz | ✗ | ✗ |  | — |
| opengear@og | ✗ | ✗ |  | — |
| opengear@og-om | ✗ | ✗ |  | — |
| stormshield@sn | ✗ | ✗ |  | — |
| zpe@nodegrid | ✓ | ✓ |  | CLI |
| nokia@timos | ✓ | ✓ |  | CLI |
| citrix@adc | ✗ | ✗ |  | — |

---

## Commands

| Vendor / Family | Command | Notes | Transport |
|-----------------|---------|-------|-----------|
| fortinet@fortiswitch | `diagnose ipv6 neighbor-cache list` |  | CLI |
| hpe@aruba | `GET /network-monitoring/v1/gateways/<serial-number>/vlans` | Aruba New Central; the show command runs over the showCommands runner. The VLAN endpoint is read to keep only neighbours on an interface l3Interfaces also emits | API |
| hpe@aruba | `POST /network-troubleshooting/v1/gateways/<serial-number>/showCommands` | Aruba New Central; the show command runs over the showCommands runner. The VLAN endpoint is read to keep only neighbours on an interface l3Interfaces also emits | API |
| hpe@aruba | `show ipv6 neighbors` | Aruba New Central; the show command runs over the showCommands runner. The VLAN endpoint is read to keep only neighbours on an interface l3Interfaces also emits | API |
| hpe@arubacx | `GET /network-monitoring/v1/switches/<serial-number>/vlans` | Aruba New Central; both neighbor spellings run over the showCommands runner, the bare one as a fallback where the per-serial allow-list refuses all-vrfs. The VLAN endpoint and the running-config are read to keep only neighbours on an interface l3Interfaces also emits | API |
| hpe@arubacx | `POST /network-troubleshooting/v1/cx/<serial-number>/showCommands` | Aruba New Central; both neighbor spellings run over the showCommands runner, the bare one as a fallback where the per-serial allow-list refuses all-vrfs. The VLAN endpoint and the running-config are read to keep only neighbours on an interface l3Interfaces also emits | API |
| hpe@arubacx | `show running-config` | Aruba New Central; both neighbor spellings run over the showCommands runner, the bare one as a fallback where the per-serial allow-list refuses all-vrfs. The VLAN endpoint and the running-config are read to keep only neighbours on an interface l3Interfaces also emits | API |
| hpe@arubacx | `show ipv6 neighbors` | Aruba New Central; both neighbor spellings run over the showCommands runner, the bare one as a fallback where the per-serial allow-list refuses all-vrfs. The VLAN endpoint and the running-config are read to keep only neighbours on an interface l3Interfaces also emits | API |
| hpe@arubacx | `show ipv6 neighbors all-vrfs` | Aruba New Central; both neighbor spellings run over the showCommands runner, the bare one as a fallback where the per-serial allow-list refuses all-vrfs. The VLAN endpoint and the running-config are read to keep only neighbours on an interface l3Interfaces also emits | API |
| zpe@nodegrid | `shell ip -6 neigh` |  | CLI |
| dlink@dgs1250 | `show ipv6 neighbors` |  | CLI |
| dlink@des3000 | `show ipv6 neighbor_cache ipif all all` |  | CLI |
| dlink@dgs1210 | `show ipv6 neighbor_cache ipif all all` |  | CLI |
| nokia@timos | `show router "<router-instance>" neighbor` |  | CLI |
| nokia@timos | `show router "<router-instance>" interface detail` |  | CLI |
| cisco@nx-os | `show ipv6 neighbor vrf all` |  | CLI |
| fortinet@fortigate | `diagnose ipv6 neighbor-cache list` |  | CLI |
| forcepoint@ngfw | `ip -6 neigh` |  | CLI |
| paloalto@pan-os | `show neighbor interface all` |  | CLI |
| arista@eos | `show ipv6 neighbors vrf all` |  | CLI |
| arista@eos | `show ipv6 neighbors` |  | CLI |
| cisco@asa | `show interface detail` |  | CLI |
| cisco@asa | `show ipv6 neighbor` |  | CLI |
| cisco@ios-xr | `show ipv6 neighbors vrf <vrf>` |  | CLI |
| cisco@ios-xr | `show ipv6 neighbors` |  | CLI |
| cisco@ios-xe | `show ipv6 neighbors vrf <vrf>` |  | CLI |
| cisco@ios-xe | `show ipv6 neighbors` |  | CLI |
| cisco@ios | `show ipv6 neighbors vrf <vrf>` |  | CLI |
| cisco@ios | `show ipv6 neighbors` |  | CLI |
| cisco@aci | `show ipv6 neighbor vrf all` |  | CLI |

---

## Legend

- **✓** = Fully Integrated
- **✗** = Not Yet Integrated
- **○** = Not Available
- **CLI** = SSH or Telnet session, **API** = vendor or controller API; in the Transport column, **✗** after one = not yet integrated over it, **—** = not integrated over any transport. A family reached over both may use the API together with CLI or instead of it.

*Generated: 2026-11-22T13:53:25.189Z*
