# Task: MAC — v8.2.0

**Version:** 8.2.0
**Category:** Basic discovery
**Description:** MAC address table
**New in this version:** No
**IPv6 Support:** No
**URL:** https://matrix.ipfabric.io/8.2.0/task/200139090

---

## Vendor Support Matrix

| Vendor / Family | Status | IPv6 | Notes | Transport |
|-----------------|--------|------|-------|-----------|
| aws | ✗ | — |  | — |
| alcatel@aos | ✓ | — |  | CLI |
| avocent@acs | ○ | — | A console server has no switching fabric. /sys/class/net is eth0, eth1 and lo, and bridge is not installed. | — |
| azure | ○ | — |  | — |
| brocade@fastiron | ✓ | — |  | CLI |
| cisco@ios | ✓ | — |  | CLI |
| cisco@ios-xe | ✓ | — |  | CLI |
| cisco@nx-os | ✓ | — |  | CLI |
| cisco@ios-xr | ✗ | — |  | — |
| cisco@asa | ○ | — |  | — |
| cisco@wlc-air | ○ | — |  | — |
| cisco@sg | ✓ | — |  | CLI |
| cisco@ftd | ✓ | — |  | CLI |
| cisco@aci | ✓ | — |  | CLI |
| cisco@meraki | ✓ | — |  | API |
| cisco@viptela | ✗ | — |  | — |
| cisco@apic | ○ | — |  | — |
| cisco@encs | ✓ | — |  | CLI |
| dell@ftos | ✓ | — |  | CLI |
| dell@powerconnect | ✓ | — |  | CLI |
| dell@os10 | ✓ | — |  | CLI |
| dlink@dgs1210 | ✓ | — |  | CLI |
| dlink@dgs1250 | ✓ | — |  | CLI |
| dlink@des3000 | ✓ | — |  | CLI |
| fs@fsos | ✓ | — |  | CLI |
| gcp | ○ | — |  | — |
| hpe@comware | ✓ | — |  | CLI |
| hpe@aruba | ✓ | — | API: Aruba New Central, over the showCommands runner - no API endpoint carries the MAC table. Only entries on an interface l2Interfaces emits are kept. CX VXLAN entries keep their VTEP but carry no VNI, the vxlan task has no API path. Gateway rows carry no source, and gateway rows on a port-channel or tunnel are not read. AOS-S has no per-VLAN fallback. aruba-iap stays n/a | CLI, API |
| hpe@arubasw | ✓ | — | API: Aruba New Central, over the showCommands runner - no API endpoint carries the MAC table. Only entries on an interface l2Interfaces emits are kept. CX VXLAN entries keep their VTEP but carry no VNI, the vxlan task has no API path. Gateway rows carry no source, and gateway rows on a port-channel or tunnel are not read. AOS-S has no per-VLAN fallback. aruba-iap stays n/a | CLI, API |
| hpe@arubacx | ✓ | — | API: Aruba New Central, over the showCommands runner - no API endpoint carries the MAC table. Only entries on an interface l2Interfaces emits are kept. CX VXLAN entries keep their VTEP but carry no VNI, the vxlan task has no API path. Gateway rows carry no source, and gateway rows on a port-channel or tunnel are not read. AOS-S has no per-VLAN fallback. aruba-iap stays n/a | CLI, API |
| hpe@3com | ✓ | — |  | CLI |
| hpe@aruba-iap | ○ | — |  | — |
| riverbed@steelhead | ○ | — |  | — |
| fortinet@fortigate | ✓ | — |  | CLI |
| fortinet@fortiswitch | ✓ | — |  | CLI |
| forcepoint@ngfw | ○ | — |  | — |
| paloalto@pan-os | ✓ | — |  | CLI |
| paloalto@prisma | ○ | — |  | — |
| juniper@junos | ✓ | — |  | CLI |
| juniper@mist | ○ | — |  | — |
| checkpoint@gaia | ✓ | — | Only CheckPoint VSX Virtual Switch | CLI, API |
| checkpoint@gaia-embedded | ○ | — |  | — |
| extreme@boss | ✓ | — |  | CLI |
| extreme@enterasys | ✓ | — |  | CLI |
| extreme@voss | ✓ | — |  | CLI |
| extreme@exos | ✓ | — |  | CLI |
| arista@eos | ✓ | — |  | CLI |
| f5@big-ip | ○ | — |  | — |
| f5@f5osa | ○ | — |  | — |
| f5@f5osc | ○ | — |  | — |
| huawei@vrp | ✓ | — |  | CLI |
| mikrotik@routeros | ✓ | — | vlanId = 0 for all records now. We need first prepeare support for software switches / bridges | CLI |
| quagga | ○ | — |  | — |
| frr | ○ | — |  | — |
| versa@vos | ✗ | — |  | — |
| silverpeak@unity | ○ | — |  | — |
| vmware@nsx-t | ✓ | — |  | API |
| vmware@velocloud | ○ | — |  | — |
| ruckus@vsz | ○ | — |  | — |
| opengear@og | ✗ | — |  | — |
| opengear@og-om | ✗ | — |  | — |
| stormshield@sn | ✗ | — |  | — |
| zpe@nodegrid | ✗ | — |  | — |
| nokia@timos | ✗ | — |  | — |
| citrix@adc | ✓ | — |  | CLI |

---

## Commands

| Vendor / Family | Command | Notes | Transport |
|-----------------|---------|-------|-----------|
| hpe@arubacx | `GET /network-monitoring/v1/switches/<serial-number>/interfaces` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| extreme@boss | `show mac-address-table` |  | CLI |
| paloalto@pan-os | `show interface <intName>` |  | CLI |
| paloalto@pan-os | `show interface all` |  | CLI |
| paloalto@pan-os | `show mac all` |  | CLI |
| juniper@junos | `show ethernet-switching vxlan-tunnel-end-point esi` |  | CLI |
| juniper@junos | `show ethernet-switching vxlan-tunnel-end-point source` |  | CLI |
| juniper@junos | `show vlans detail` |  | CLI |
| juniper@junos | `show ethernet-switching table` |  | CLI |
| hpe@aruba | `GET /network-monitoring/v1/gateways/<serial-number>/vlans` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@aruba | `GET /network-monitoring/v1/gateways/<serial-number>/ports` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@aruba | `POST /network-troubleshooting/v1/gateways/<serial-number>/showCommands` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubacx | `GET /network-monitoring/v1/switches/<serial-number>/vlans` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubacx | `GET /network-monitoring/v1/switches/<serial-number>/lag` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| extreme@boss | `show mac-address-table vid <vid>` |  | CLI |
| hpe@arubacx | `POST /network-troubleshooting/v1/cx/<serial-number>/showCommands` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubacx | `show running-config` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubacx | `show interface` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubasw | `GET /network-monitoring/v1/switches/<serial-number>/vlans` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubasw | `GET /network-monitoring/v1/switches/<serial-number>/lag` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubasw | `GET /network-monitoring/v1/switches/<serial-number>/interfaces` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubasw | `POST /network-troubleshooting/v1/aos-s/<serial-number>/showCommands` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubasw | `show running-config` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubasw | `show oobm ip` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubasw | `show oobm` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubasw | `show lldp info local-device` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubasw | `show ip route` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubasw | `show ip` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| arista@eos | `show interfaces` |  | CLI |
| citrix@adc | `show arp` |  | CLI |
| vmware@nsx-t | `GET /policy/api/v1/infra/segments/<segmentName>/ports` |  | API |
| vmware@nsx-t | `GET /policy/api/v1/infra/segments` |  | API |
| vmware@nsx-t | `GET /policy/api/v1/infra/segments/<segmentId>/ports/<portId>/mac-table?source=realtime` |  | API |
| mikrotik@routeros | `/interface bridge host print detail without-paging where !local` |  | CLI |
| fortinet@fortiswitch | `diagnose switch mac-address list` |  | CLI |
| fortinet@fortigate | `diagnose netlink brctl name host <bridge>` |  | CLI |
| fortinet@fortigate | `diagnose netlink brctl list` |  | CLI |
| fortinet@fortigate | `show system interface` |  | CLI |
| fortinet@fortigate | `get system status` |  | CLI |
| huawei@vrp | `display vxlan vni` |  | CLI |
| huawei@vrp | `display interface` |  | CLI |
| huawei@vrp | `display mac-address` |  | CLI |
| hpe@arubasw | `show interfaces all` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| arista@eos | `show interfaces vxlan 1` |  | CLI |
| arista@eos | `show vxlan address-table` |  | CLI |
| arista@eos | `show mac address-table` |  | CLI |
| extreme@exos | `show fdb` |  | CLI |
| extreme@voss | `show i-sid` |  | CLI |
| extreme@voss | `show isis spbm i-sid all` |  | CLI |
| extreme@voss | `show isis` |  | CLI |
| extreme@voss | `show i-sid mac-address-entry` |  | CLI |
| extreme@voss | `show vlan mac-address-entry` |  | CLI |
| extreme@voss | `show mlt` |  | CLI |
| extreme@enterasys | `show mac` |  | CLI |
| extreme@boss | `show vlan` |  | CLI |
| cisco@nx-os | `show nve vni` | Nexus 9000v - l2fwder replaces mac table | CLI |
| cisco@ftd | `show mac-address-table` |  | CLI |
| cisco@sg | `show mac address-table` |  | CLI |
| cisco@ios-xe | `show run \| inc qos queue-stats-frame-count` | "show run | inc qos queue-stats-frame-count" for selected IOS-XE platforms (cat3k/cat9k) | CLI |
| cisco@ios-xe | ` show bridge-domain` | "show run | inc qos queue-stats-frame-count" for selected IOS-XE platforms (cat3k/cat9k) | CLI |
| cisco@ios-xe | `show interfaces` | "show run | inc qos queue-stats-frame-count" for selected IOS-XE platforms (cat3k/cat9k) | CLI |
| cisco@ios-xe | `show mac-address` | "show run | inc qos queue-stats-frame-count" for selected IOS-XE platforms (cat3k/cat9k) | CLI |
| cisco@ios-xe | `show mac address` | "show run | inc qos queue-stats-frame-count" for selected IOS-XE platforms (cat3k/cat9k) | CLI |
| cisco@encs | `show switch mac` |  | CLI |
| cisco@ios | `show mac-address` |  | CLI |
| cisco@ios | `show mac address` |  | CLI |
| cisco@nx-os | `show feature-set` | Nexus 9000v - l2fwder replaces mac table | CLI |
| cisco@nx-os | `show fabricpath route` | Nexus 9000v - l2fwder replaces mac table | CLI |
| cisco@nx-os | `show vpc` | Nexus 9000v - l2fwder replaces mac table | CLI |
| cisco@ftd | `show interface` |  | CLI |
| cisco@nx-os | `show interfaces` | Nexus 9000v - l2fwder replaces mac table | CLI |
| cisco@nx-os | `show system internal l2fwder mac` | Nexus 9000v - l2fwder replaces mac table | CLI |
| cisco@nx-os | `show mac address` | Nexus 9000v - l2fwder replaces mac table | CLI |
| checkpoint@gaia | `POST /web_api/show-gateways-and-servers` |  | API |
| checkpoint@gaia | `set mdps environment <plane>` |  | CLI |
| checkpoint@gaia | `show bridging groups` |  | CLI |
| checkpoint@gaia | `show interfaces all` |  | CLI |
| brocade@fastiron | `show lag` |  | CLI |
| brocade@fastiron | `show mac-address` |  | CLI |
| alcatel@aos | `show service mesh-sdp spb` |  | CLI |
| alcatel@aos | `show mac-learning domain spb` |  | CLI |
| alcatel@aos | `show mac-learning` |  | CLI |
| dlink@dgs1210 | `show fdb` |  | CLI |
| hpe@arubacx | `show ip interface brief` |  | CLI |
| hpe@arubacx | `show interface vxlan vni` |  | CLI |
| hpe@arubacx | `show interface vxlan vteps detail` |  | CLI |
| hpe@arubacx | `show mac-address-table` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | CLI, API |
| hpe@arubasw | `show vlans` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | CLI, API |
| hpe@arubasw | `show mac-address vlan <vlanId>` |  | CLI |
| hpe@arubasw | `show mac-address` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | CLI, API |
| hpe@aruba | `show datapath bridge` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | CLI, API |
| hpe@3com | `display mac-address` |  | CLI |
| hpe@comware | `display mac-address` |  | CLI |
| fs@fsos | `show mac-address-table` |  | CLI |
| fs@fsos | `show mac address-table` |  | CLI |
| dlink@des3000 | `show fdb` |  | CLI |
| alcatel@aos | `show mac-address-table` |  | CLI |
| dlink@dgs1250 | `show mac-address-table` |  | CLI |
| dell@os10 | `show mac address-table` |  | CLI |
| dell@powerconnect | `show mac address-table` |  | CLI |
| dell@ftos | `show mac address-table` | The second command is for Dell Ftos version >= 10 | CLI |
| dell@ftos | `show mac-address-table` | The second command is for Dell Ftos version >= 10 | CLI |
| cisco@meraki | `GET /networks/<networkId>/switch/stacks` |  | API |
| cisco@meraki | `POST /devices/<serial>/liveTools/macTable` |  | API |
| cisco@meraki | `GET /devices/<serial>/liveTools/macTable/<macTableId>` |  | API |
| cisco@meraki | `GET /devices/<deviceSn>/clients` |  | API |
| cisco@aci | `show vpc` |  | CLI |
| cisco@aci | `show mac address-table` |  | CLI |
| cisco@ftd | `show interface detail` |  | CLI |

---

## Legend

- **✓** = Fully Integrated
- **✗** = Not Yet Integrated
- **○** = Not Available
- **CLI** = SSH or Telnet session, **API** = vendor or controller API; in the Transport column, **✗** after one = not yet integrated over it, **—** = not integrated over any transport. A family reached over both may use the API together with CLI or instead of it.

*Generated: 2026-11-22T13:53:18.951Z*
