# Task: ARP — v8.2.0

**Version:** 8.2.0
**Category:** Basic discovery
**Description:** ARP table
**New in this version:** No
**IPv6 Support:** No
**URL:** https://matrix.ipfabric.io/8.2.0/task/200125117

---

## Vendor Support Matrix

| Vendor / Family | Status | IPv6 | Notes | Transport |
|-----------------|--------|------|-------|-----------|
| aws | ✗ | — |  | — |
| alcatel@aos | ✓ | — |  | CLI |
| avocent@acs | ✗ | — |  | — |
| azure | ✓ | — |  | API |
| brocade@fastiron | ✓ | — |  | CLI |
| cisco@ios | ✓ | — |  | CLI |
| cisco@ios-xe | ✓ | — |  | CLI |
| cisco@nx-os | ✓ | — |  | CLI |
| cisco@ios-xr | ✓ | — |  | CLI |
| cisco@asa | ✓ | — |  | CLI |
| cisco@wlc-air | ○ | — |  | — |
| cisco@sg | ✓ | — |  | CLI |
| cisco@ftd | ✓ | — |  | CLI |
| cisco@aci | ✓ | — |  | CLI |
| cisco@meraki | ✓ | — | only applicable for MS devices (switches) | API |
| cisco@viptela | ✓ | — |  | CLI ✗, API |
| cisco@apic | ○ | — |  | — |
| cisco@encs | ✓ | — |  | CLI |
| dell@ftos | ✓ | — |  | CLI |
| dell@powerconnect | ✓ | — |  | CLI |
| dell@os10 | ✓ | — |  | CLI |
| dlink@dgs1210 | ✓ | — |  | CLI |
| dlink@dgs1250 | ✓ | — |  | CLI |
| dlink@des3000 | ✓ | — |  | CLI |
| fs@fsos | ✓ | — |  | CLI |
| gcp | ○ | — |  | — |
| hpe@comware | ✓ | — |  | CLI |
| hpe@aruba | ✓ | — | API: Aruba New Central, over the showCommands runner - no API endpoint carries ARP. Only entries on an interface l3Interfaces emits are kept. CX reads all-vrfs, which omits the mgmt VRF, and its allow-list refuses show arp vrf <name>. The AOS-S oobm ARP table is not read. aruba-iap has no L3 interface source, so it stays n/a | CLI, API |
| hpe@arubasw | ✓ | — | API: Aruba New Central, over the showCommands runner - no API endpoint carries ARP. Only entries on an interface l3Interfaces emits are kept. CX reads all-vrfs, which omits the mgmt VRF, and its allow-list refuses show arp vrf <name>. The AOS-S oobm ARP table is not read. aruba-iap has no L3 interface source, so it stays n/a | CLI, API |
| hpe@arubacx | ✓ | — | API: Aruba New Central, over the showCommands runner - no API endpoint carries ARP. Only entries on an interface l3Interfaces emits are kept. CX reads all-vrfs, which omits the mgmt VRF, and its allow-list refuses show arp vrf <name>. The AOS-S oobm ARP table is not read. aruba-iap has no L3 interface source, so it stays n/a | CLI, API |
| hpe@3com | ✓ | — |  | CLI |
| hpe@aruba-iap | ○ | — |  | — |
| riverbed@steelhead | ✓ | — |  | CLI |
| fortinet@fortigate | ✓ | — |  | CLI |
| fortinet@fortiswitch | ✓ | — |  | CLI |
| forcepoint@ngfw | ✓ | — |  | CLI |
| paloalto@pan-os | ✓ | — |  | CLI |
| paloalto@prisma | ✗ | — |  | — |
| juniper@junos | ✓ | — |  | CLI |
| juniper@mist | ○ | — |  | — |
| checkpoint@gaia | ✓ | — |  | CLI |
| checkpoint@gaia-embedded | ✓ | — |  | CLI |
| extreme@boss | ✓ | — |  | CLI |
| extreme@enterasys | ✓ | — |  | CLI |
| extreme@voss | ✓ | — |  | CLI |
| extreme@exos | ✓ | — |  | CLI |
| arista@eos | ✓ | — |  | CLI |
| f5@big-ip | ✓ | — |  | CLI |
| f5@f5osa | ○ | — |  | — |
| f5@f5osc | ○ | — |  | — |
| huawei@vrp | ✓ | — |  | CLI |
| mikrotik@routeros | ✓ | — |  | CLI |
| quagga | ○ | — |  | — |
| frr | ○ | — |  | — |
| versa@vos | ✓ | — |  | CLI ✗, API |
| silverpeak@unity | ✓ | — |  | API |
| vmware@nsx-t | ✓ | — |  | API |
| vmware@velocloud | ✓ | — |  | API |
| ruckus@vsz | ✗ | — |  | — |
| opengear@og | ✓ | — |  | CLI |
| opengear@og-om | ✓ | — |  | CLI |
| stormshield@sn | ✓ | — |  | CLI |
| zpe@nodegrid | ✓ | — |  | CLI |
| nokia@timos | ✓ | — |  | CLI |
| citrix@adc | ✓ | — |  | CLI |

---

## Commands

| Vendor / Family | Command | Notes | Transport |
|-----------------|---------|-------|-----------|
| checkpoint@gaia | `show arp static all` |  | CLI |
| fortinet@fortigate | `get system arp` |  | CLI |
| fortinet@fortiswitch | `get system arp` |  | CLI |
| juniper@junos | `show arp no-resolve` |  | CLI |
| paloalto@pan-os | `show arp all` |  | CLI |
| paloalto@pan-os | `show arp management` |  | CLI |
| riverbed@steelhead | `show arp` |  | CLI |
| riverbed@steelhead | `show interfaces` |  | CLI |
| checkpoint@gaia | `show arp dynamic all` |  | CLI |
| hpe@aruba | `GET /network-monitoring/v1/gateways/<serial-number>/vlans` | Aruba New Central; the show command runs over the showCommands runner. The VLAN endpoint is the l3Interfaces dependency, read to keep only entries on an interface it emits | API |
| checkpoint@gaia | `show mdps state` |  | CLI |
| checkpoint@gaia | `show route all` |  | CLI |
| checkpoint@gaia | `set mdps environment <plane>` |  | CLI |
| checkpoint@gaia-embedded | `arp` |  | CLI |
| extreme@boss | `show arp-table` |  | CLI |
| extreme@enterasys | `show arp` |  | CLI |
| extreme@voss | `show ip arp` |  | CLI |
| hpe@arubasw | `show arp vlan <vlanId>` | Aruba New Central; one show arp vlan per SVI l3Interfaces emits, over the showCommands runner. The running-config, show oobm ip and the VLAN endpoint are its dependencies, read to keep only entries on an interface it emits | API |
| hpe@aruba | `show arp` | Aruba New Central; the show command runs over the showCommands runner. The VLAN endpoint is the l3Interfaces dependency, read to keep only entries on an interface it emits | CLI, API |
| hpe@arubasw | `show arp` |  | CLI |
| hpe@arubasw | `show ip` |  | CLI |
| hpe@arubasw | `show mac-address vlan <vlanId>` |  | CLI |
| hpe@arubasw | `show running-config` | Aruba New Central; one show arp vlan per SVI l3Interfaces emits, over the showCommands runner. The running-config, show oobm ip and the VLAN endpoint are its dependencies, read to keep only entries on an interface it emits | CLI, API |
| hpe@arubasw | `show vlans` |  | CLI |
| hpe@arubacx | `show arp all-vrfs` | Aruba New Central; both spellings run over the showCommands runner, the bare one as a fallback where the device rejects all-vrfs. The running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only entries on an interface it emits | CLI, API |
| hpe@arubacx | `show arp` | Aruba New Central; both spellings run over the showCommands runner, the bare one as a fallback where the device rejects all-vrfs. The running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only entries on an interface it emits | CLI, API |
| extreme@voss | `show ip interface` |  | CLI |
| hpe@arubasw | `show oobm ip` | Aruba New Central; one show arp vlan per SVI l3Interfaces emits, over the showCommands runner. The running-config, show oobm ip and the VLAN endpoint are its dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubasw | `POST /network-troubleshooting/v1/aos-s/<serial-number>/showCommands` | Aruba New Central; one show arp vlan per SVI l3Interfaces emits, over the showCommands runner. The running-config, show oobm ip and the VLAN endpoint are its dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubasw | `GET /network-monitoring/v1/switches/<serial-number>/vlans` | Aruba New Central; one show arp vlan per SVI l3Interfaces emits, over the showCommands runner. The running-config, show oobm ip and the VLAN endpoint are its dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubacx | `show running-config` | Aruba New Central; both spellings run over the showCommands runner, the bare one as a fallback where the device rejects all-vrfs. The running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubacx | `POST /network-troubleshooting/v1/cx/<serial-number>/showCommands` | Aruba New Central; both spellings run over the showCommands runner, the bare one as a fallback where the device rejects all-vrfs. The running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@arubacx | `GET /network-monitoring/v1/switches/<serial-number>/vlans` | Aruba New Central; both spellings run over the showCommands runner, the bare one as a fallback where the device rejects all-vrfs. The running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only entries on an interface it emits | API |
| hpe@aruba | `POST /network-troubleshooting/v1/gateways/<serial-number>/showCommands` | Aruba New Central; the show command runs over the showCommands runner. The VLAN endpoint is the l3Interfaces dependency, read to keep only entries on an interface it emits | API |
| nokia@timos | `show router "<router-instance>" interface detail` |  | CLI |
| versa@vos | `GET /vnms/dashboard/appliance/<appliance>/live?command=arp/all` |  | API |
| silverpeak@unity | `POST /gms/rest/broadcastCli cmdList: "show arp"` |  | API |
| silverpeak@unity | `GET /gms/rest/action/status?key=<statusKey>` |  | API |
| vmware@nsx-t | `GET /api/v1/logical-routers/` |  | API |
| vmware@nsx-t | `GET /api/v1/logical-ports` |  | API |
| vmware@nsx-t | `GET /api/v1/logical-router-ports?logical_router_id=<router-id>` |  | API |
| vmware@nsx-t | `GET /api/v1/logical-router-ports/<portId>/arp-table?source=realtime&transport_node_id=<transportNodeId>` |  | API |
| vmware@velocloud | `WSS /ws/<ARP_DUMP>` |  | API |
| stormshield@sn | `arp -a` |  | CLI |
| nokia@timos | `show router "<router-instance>" arp` |  | CLI |
| nokia@timos | `show service service-using` |  | CLI |
| nokia@timos | `show service <service-id> interface detail` |  | CLI |
| citrix@adc | `show arp` |  | CLI |
| citrix@adc | `show cluster instance` |  | CLI |
| citrix@adc | `switch partition` |  | CLI |
| zpe@nodegrid | `shell cat /proc/net/arp` |  | CLI |
| hpe@3com | `display arp` |  | CLI |
| opengear@og-om | `arp -n` |  | CLI |
| opengear@og | `arp` |  | CLI |
| mikrotik@routeros | `/ip arp print detail without-paging` |  | CLI |
| f5@big-ip | `list net self recursive` |  | CLI |
| f5@big-ip | `list net self` |  | CLI |
| f5@big-ip | `show net arp all` |  | CLI |
| huawei@vrp | `display arp all` |  | CLI |
| huawei@vrp | `display arp` |  | CLI |
| azure | `GET /expressRouteCircuits/<circuitName>/peerings/<peeringName>/arpTables/<devicePath>` |  | API |
| arista@eos | `show ip arp vrf <vrfName>` |  | CLI |
| arista@eos | `show ip arp` |  | CLI |
| extreme@exos | `show virtual router` |  | CLI |
| extreme@exos | `show iparp vr <vrName>` |  | CLI |
| extreme@voss | `show ip vrf` |  | CLI |
| extreme@voss | `show ip interface vrf <vrfName>` |  | CLI |
| cisco@nx-os | `show vrf all detail` |  | CLI |
| cisco@ios-xe | `show ip interface` |  | CLI |
| cisco@ios-xe | `show ipv6 interface` |  | CLI |
| cisco@ios-xe | `show standby brief` |  | CLI |
| cisco@ios-xe | `show glbp brief` |  | CLI |
| cisco@ios-xe | `show vrrp brief` |  | CLI |
| cisco@ios-xe | `show interface` |  | CLI |
| cisco@nx-os | `show ip arp` |  | CLI |
| cisco@nx-os | `show ip arp vrf <vrf>` |  | CLI |
| cisco@ios-xe | `show ip vrf detail` |  | CLI |
| cisco@nx-os | `show ip interface vrf all` |  | CLI |
| cisco@nx-os | `show ipv6 interface vrf all` |  | CLI |
| cisco@nx-os | `show hsrp brief` |  | CLI |
| cisco@nx-os | `show glbp brief` |  | CLI |
| cisco@nx-os | `show vrrp` |  | CLI |
| cisco@nx-os | `show interface` |  | CLI |
| cisco@nx-os | `show running configuration` |  | CLI |
| cisco@ios | `show ipv6 interface` |  | CLI |
| alcatel@aos | `show ip interface` |  | CLI |
| brocade@fastiron | `show arp` |  | CLI |
| forcepoint@ngfw | `ip neighbor` |  | CLI |
| cisco@ios | `show ip arp` |  | CLI |
| cisco@ios | `show ip arp vrf <vrf>` |  | CLI |
| cisco@ios | `show vrf detail` |  | CLI |
| cisco@ios | `show ip vrf detail` |  | CLI |
| cisco@ios | `show ip interface` |  | CLI |
| cisco@ios-xr | `show adjacency ipv4 detail` |  | CLI |
| cisco@ios | `show standby brief` |  | CLI |
| cisco@ios | `show glbp brief` |  | CLI |
| cisco@ios | `show vrrp brief` |  | CLI |
| cisco@ios | `show interface` |  | CLI |
| cisco@ios-xe | `show ip arp` |  | CLI |
| cisco@ios-xe | `show ip arp vrf <vrf>` |  | CLI |
| cisco@ios-xe | `show vrf detail` |  | CLI |
| fs@fsos | `show arp` |  | CLI |
| cisco@viptela | `GET /dataservice/device/arp?deviceId=<deviceId>` |  | API |
| dell@ftos | `show arp` |  | CLI |
| dell@powerconnect | `show arp` |  | CLI |
| dell@os10 | `show ip arp` |  | CLI |
| dell@os10 | `show ip arp vrf <vrfName>` |  | CLI |
| dlink@dgs1250 | `show arp` |  | CLI |
| dlink@dgs1210 | `show arpentry` |  | CLI |
| dlink@des3000 | `show arpentry` |  | CLI |
| cisco@aci | `show ip arp vrf all` |  | CLI |
| fs@fsos | `show ip arp` |  | CLI |
| fs@fsos | `show arp vrf <vrfname>` |  | CLI |
| fs@fsos | `show ip arp vrf <vrfName>` |  | CLI |
| fs@fsos | `show management arp` |  | CLI |
| hpe@comware | `display arp` |  | CLI |
| hpe@comware | `display ip interface` |  | CLI |
| hpe@comware | `display ip vpn-instance` |  | CLI |
| alcatel@aos | `show arp` |  | CLI |
| cisco@sg | `show arp` |  | CLI |
| cisco@ftd | `show interface detail` |  | CLI |
| cisco@ftd | `show interface` |  | CLI |
| cisco@ftd | `show arp` |  | CLI |
| cisco@asa | `show interface detail` |  | CLI |
| cisco@asa | `show interface` |  | CLI |
| cisco@asa | `show arp` |  | CLI |
| cisco@encs | `show switch arp` |  | CLI |
| cisco@encs | `support show arp` |  | CLI |
| cisco@meraki | `GET /devices/<sn>/switch/ports` |  | API |
| cisco@meraki | `GET /devices/<sn>/switch/routing/interfaces` |  | API |
| cisco@meraki | `POST /devices/<serial>/liveTools/arpTable` |  | API |
| cisco@meraki | `GET /devices/<serial>/liveTools/arpTable/<arpTableId>` |  | API |
| cisco@meraki | `GET /networks/<networkId>/appliance/vlans` |  | API |
| cisco@meraki | `GET /devices/<deviceSn>/clients` |  | API |

---

## Legend

- **✓** = Fully Integrated
- **✗** = Not Yet Integrated
- **○** = Not Available
- **CLI** = SSH or Telnet session, **API** = vendor or controller API; in the Transport column, **✗** after one = not yet integrated over it, **—** = not integrated over any transport. A family reached over both may use the API together with CLI or instead of it.

*Generated: 2026-11-22T13:53:24.273Z*
