Family: hpe 3com (v8.2.0) ================================================== Vendor: hpe Family: 3com Transport: CLI New: No Commands: -------------------------------------------------- Routing table: display ip interface [CLI] L3 Interfaces: display ip interface [CLI] L3 Interfaces: display vrrp verbose [CLI] MAC: display mac-address [CLI] Neighbors: display ndp [CLI] Neighbors: display lldp neighbor-information [CLI] Link aggregations: display interface [CLI] Link aggregations: display link-aggregation verbose [CLI] Routing table: display ip routing-table verbose [CLI] L2 Interfaces: display link-aggregation verbose [CLI] Routing table: display vrrp verbose [CLI] SN: display device manuinfo [CLI] STP: display stp [CLI] STP: display vlan all [CLI] STP: display interface [CLI] STP: display stp region-configuration [CLI] STP: display voice vlan status [CLI] Initial device discovery: display version [CLI] L2 Interfaces: display voice vlan status [CLI] L2 Interfaces: display interface [CLI] FHRP: display vrrp verbose [CLI] DNS resolver: display current-configuration [CLI] DHCPv4 Relays: display current-configuration [CLI] Startup config: display saved-configuration [CLI] Current config: display current-configuration [CLI] Configuration saved: display current-configuration [CLI] Configuration saved: display saved-configuration [CLI] Device info: display memory [CLI] Device info: display tcp status [CLI] Device info: display device manuinfo [CLI] Device info: display version [CLI] ARP: display arp [CLI] Initial device discovery: undo terminal monitor [CLI] Task Support: -------------------------------------------------- Basic discovery: ✓ ARP [CLI] ✓ Device info [CLI] ○ Disable pagination ✓ FHRP (IPv6: ✗) [CLI] ✓ Initial device discovery [CLI] ✗ IPv6 Neighbor Discovery (IPv6: ✗) ✓ L2 Interfaces [CLI] ✓ L3 Interfaces (IPv6: ✗) [CLI] ✓ Link aggregations [CLI] ✓ MAC [CLI] ✓ Neighbors (IPv6: ✗) [CLI] ✓ Routing table (IPv6: ✗) [CLI] ○ Serial ports ✓ SN [CLI] ✓ STP [CLI] ○ Virtual Contexts ✗ Vlan Configuration: ✓ Configuration saved [CLI] ✓ Current config [CLI] ✓ Startup config [CLI] Hardware: ○ Cluster ✓ End of Life data [CLI] ○ Extenders ✗ PoE ✗ Power supplies & fans ✗ Stacking ✗ Transceivers ○ VSS Hybrid discovery: ○ snCheck Management: ✓ DHCPv4 Relays (IPv6: ✗) [CLI] ✗ DHCPv4 Servers (IPv6: ✗) ✓ DNS resolver (IPv6: ✓) [CLI] ✗ IP Flow (IPv6: ✗) ○ License ✗ NTP (IPv6: ✗) ✗ Port mirroring ✗ PTP (IPv6: ✗) ✗ SNMP (IPv6: ✗) ✗ Syslog (IPv6: ✗) ✗ Unidirectional Link Detection MPLS: ○ Circuit cross-connect ○ MPLS forwarding ○ MPLS LDP ✗ RSVP ○ VPLS ○ VPWS Multicast: ✗ IGMP ✗ IGMP Snooping ✗ MAC multicast address table ✗ MROUTE ✗ PIM Other: ○ Cloud network interfaces (IPv6: ○) ✗ PPPoE (IPv6: ✗) Policy: ✗ NAT44 QoS: ✗ QoS Routing: ○ BGP Advertised Routes (IPv6: ○) ○ Fabric Path ✗ Policy-based Routing (IPv6: ✗) ✗ Route summary (IPv6: ✗) ○ Routing policies ✗ VRF Routing protocols: ✗ BGP neighbors (IPv6: ✗) ○ EIGRP (IPv6: ○) ✗ IS-IS (IPv6: ✗) ○ Lisp (IPv6: ○) ✗ OSPF ✗ OSPFv3 (IPv6: ✗) ✗ RIP SDN: ○ APIC (IPv6: ○) ○ Cisco ACI (IPv6: ○) ○ Virtual machines ○ VXLAN SDWAN: ○ SD-WAN sites Security: ✗ AAA (IPv6: ✗) ✗ ACL (IPv6: ✗) ✗ DHCPv4 Snooping (IPv6: ✗) ○ DMVPN (IPv6: ○) ✗ Error disabled interfaces ○ IPsec (IPv6: ○) ○ LSVPN (IPv6: ○) ○ Prefix lists (IPv6: ○) ✗ Secured access ports ✗ Storm control ✗ STP port security ○ Virtual servers (IPv6: ○) ○ Zone firewall (IPv6: ○) Wireless: ○ Wireless AP ○ Wireless clients ○ Wireless Controller with APs All Families from hpe: -------------------------------------------------- hpe@comware hpe@aruba hpe@arubasw hpe@arubacx hpe@3com <-- current hpe@aruba-iap Legend: ✓=Full, ✗=Not Yet, ○=N/A Transport: [CLI] = SSH or Telnet session, [API] = vendor or controller API, ✗ after one = not yet integrated over it