Family: hpe arubacx (v8.2.0) ================================================== Vendor: hpe Family: arubacx Transport: CLI, API New: No Commands: -------------------------------------------------- OSPF: show ip ospf all-vrfs [CLI] Routing table: show ip route [Aruba New Central, over the showCommands runner. show ip route is the fallback when all-vrfs is refused (refused itself on the CX-6200F; same fallback as the arp runner). show running-config supplies the mgmt default gateway; with the VLAN endpoint it is the l3Interfaces dependency that CEF entries are filtered against] [CLI, API] Route summary: show ip route summary [CLI] Route summary: show ip route summary all-vrfs [CLI] Link aggregations: GET /network-monitoring/v1/switches//interfaces [Aruba New Central. The LAG endpoint reports no protocol (type is null on LACP aggregates too), so poProto is empty; the channel state is derived - up when a member is up] [API] Link aggregations: GET /network-monitoring/v1/switches//lag [Aruba New Central. The LAG endpoint reports no protocol (type is null on LACP aggregates too), so poProto is empty; the channel state is derived - up when a member is up] [API] Link aggregations: show lacp interfaces multi-chassis [CLI] Link aggregations: show vsx status [CLI] Link aggregations: show vsx brief [CLI] Link aggregations: show interface [CLI] Link aggregations: show interface lag [CLI] Policy-based Routing: show running-config [CLI] OSPF: show ip ospf neighbors detail all-vrfs [CLI] OSPF: show ip ospf neighbors detail [CLI] OSPF: show ip ospf interface all-vrfs [CLI] OSPF: show ip ospf interface [CLI] Routing table: show ip route all-vrfs [Aruba New Central, over the showCommands runner. show ip route is the fallback when all-vrfs is refused (refused itself on the CX-6200F; same fallback as the arp runner). show running-config supplies the mgmt default gateway; with the VLAN endpoint it is the l3Interfaces dependency that CEF entries are filtered against] [CLI, API] NTP: show ntp associations [CLI] Neighbors: show cdp neighbor info [CLI] Neighbors: show cdp neighbor info [CLI] Neighbors: show lldp neighbor info [CLI] Neighbors: show lldp neighbor info [CLI] IPv6 Neighbor Discovery: GET /network-monitoring/v1/switches//vlans [Aruba New Central; both neighbor spellings run over the showCommands runner, the bare one as a fallback where the per-serial allow-list refuses all-vrfs. The VLAN endpoint and the running-config are read to keep only neighbours on an interface l3Interfaces also emits] [API] IPv6 Neighbor Discovery: POST /network-troubleshooting/v1/cx//showCommands [Aruba New Central; both neighbor spellings run over the showCommands runner, the bare one as a fallback where the per-serial allow-list refuses all-vrfs. The VLAN endpoint and the running-config are read to keep only neighbours on an interface l3Interfaces also emits] [API] IPv6 Neighbor Discovery: show running-config [Aruba New Central; both neighbor spellings run over the showCommands runner, the bare one as a fallback where the per-serial allow-list refuses all-vrfs. The VLAN endpoint and the running-config are read to keep only neighbours on an interface l3Interfaces also emits] [API] IPv6 Neighbor Discovery: show ipv6 neighbors [Aruba New Central; both neighbor spellings run over the showCommands runner, the bare one as a fallback where the per-serial allow-list refuses all-vrfs. The VLAN endpoint and the running-config are read to keep only neighbours on an interface l3Interfaces also emits] [API] IPv6 Neighbor Discovery: show ipv6 neighbors all-vrfs [Aruba New Central; both neighbor spellings run over the showCommands runner, the bare one as a fallback where the per-serial allow-list refuses all-vrfs. The VLAN endpoint and the running-config are read to keep only neighbours on an interface l3Interfaces also emits] [API] PIM: show ip pim bsr all-vrfs [CLI] PIM: show ip pim neighbor all-vrfs [CLI] PIM: show ip pim rp-set all-vrfs [CLI] PIM: show ip pim interface all-vrfs [CLI] MROUTE: show ip mroute all-vrfs [CLI] Stacking: show vsf detail [CLI] VXLAN: show ip interface all-vrfs [CLI] VXLAN: show ip interface [CLI] VXLAN: show interface vxlan vni [CLI] VXLAN: show interface vxlan vteps detail [CLI] VRF: show vrf [CLI] Vlan: GET /network-monitoring/v1/switches//vlans [Aruba New Central; id, name and operational status] [API] Vlan: show vlan [CLI] Transceivers: show interface transceiver detail [CLI] Syslog: show running-config [CLI] STP: POST /network-troubleshooting/v1/cx//showCommands [Aruba New Central. RPVST root cost comes only from show spanning-tree summary root, refused by the lab CX-6200F allow-list] [API] STP: show vlan [Aruba New Central. RPVST root cost comes only from show spanning-tree summary root, refused by the lab CX-6200F allow-list] [CLI, API] STP: show spanning-tree summary root [Aruba New Central. RPVST root cost comes only from show spanning-tree summary root, refused by the lab CX-6200F allow-list] [CLI, API] STP: show spanning-tree mst detail [Aruba New Central. RPVST root cost comes only from show spanning-tree summary root, refused by the lab CX-6200F allow-list] [CLI, API] STP: show spanning-tree detail [Aruba New Central. RPVST root cost comes only from show spanning-tree summary root, refused by the lab CX-6200F allow-list] [CLI, API] Stacking: show vsf link [CLI] IGMP Snooping: show ip igmp snooping [CLI] SNMP: show running-config [CLI] SN: show system [CLI] SN: GET /network-monitoring/v1/devices [the tasker builds the ver from this call; the task sends no request of its own] [API] Secured access ports: show port-access clients detail [CLI] Routing table: GET /network-monitoring/v1/switches//vlans [Aruba New Central, over the showCommands runner. show ip route is the fallback when all-vrfs is refused (refused itself on the CX-6200F; same fallback as the arp runner). show running-config supplies the mgmt default gateway; with the VLAN endpoint it is the l3Interfaces dependency that CEF entries are filtered against] [API] Routing table: POST /network-troubleshooting/v1/cx//showCommands [Aruba New Central, over the showCommands runner. show ip route is the fallback when all-vrfs is refused (refused itself on the CX-6200F; same fallback as the arp runner). show running-config supplies the mgmt default gateway; with the VLAN endpoint it is the l3Interfaces dependency that CEF entries are filtered against] [API] Routing table: show running-config [Aruba New Central, over the showCommands runner. show ip route is the fallback when all-vrfs is refused (refused itself on the CX-6200F; same fallback as the arp runner). show running-config supplies the mgmt default gateway; with the VLAN endpoint it is the l3Interfaces dependency that CEF entries are filtered against] [API] Routing table: show ip interface brief [CLI] Routing table: show interface vxlan vni [CLI] Routing table: show interface vxlan vteps detail [CLI] Routing table: show interface mgmt [CLI] Routing table: show ip route [CLI] Routing table: show ip route all-vrfs [CLI] Routing table: show ip route summary [CLI] Routing table: show ip route summary all-vrfs [CLI] Device info: GET /network-monitoring/v1/devices [the tasker builds the ver from this call; the task sends no request of its own] [API] Power supplies & fans: show environment [CLI] DNS resolver: show ip dns [CLI] DHCPv4 Relays: show dhcp-relay [CLI] DHCPv4 Relays: show ip helper-address [CLI] Startup config: show startup-config [CLI] Current config: POST /network-troubleshooting/v1/cx//showCommands [API] Current config: show running-config [CLI, API] Configuration saved: show running-config [CLI] Configuration saved: show startup-config [CLI] Device info: show boot-history [CLI] Device info: show images [CLI] Device info: show lldp local-device [CLI] Device info: show module [CLI] Device info: show system [CLI] Device info: top memory [CLI] Power supplies & fans: show system [CLI] BGP neighbors: show bpg all neighbors [CLI] BGP neighbors: show bgp all-vrf all neighbors [CLI] ARP: GET /network-monitoring/v1/switches//vlans [Aruba New Central; both spellings run over the showCommands runner, the bare one as a fallback where the device rejects all-vrfs. The running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only entries on an interface it emits] [API] ARP: POST /network-troubleshooting/v1/cx//showCommands [Aruba New Central; both spellings run over the showCommands runner, the bare one as a fallback where the device rejects all-vrfs. The running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only entries on an interface it emits] [API] ARP: show running-config [Aruba New Central; both spellings run over the showCommands runner, the bare one as a fallback where the device rejects all-vrfs. The running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only entries on an interface it emits] [API] ARP: show arp [Aruba New Central; both spellings run over the showCommands runner, the bare one as a fallback where the device rejects all-vrfs. The running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only entries on an interface it emits] [CLI, API] ARP: show arp all-vrfs [Aruba New Central; both spellings run over the showCommands runner, the bare one as a fallback where the device rejects all-vrfs. The running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only entries on an interface it emits] [CLI, API] ACL: show running-config [CLI] AAA: show aaa server-groups [CLI] AAA: show aaa authorization [CLI] AAA: show aaa authentication [CLI] AAA: show aaa accounting [CLI] Initial device discovery: GET /network-monitoring/v1/switches [the tasker builds the ver from these calls; an MSP login first lists tenants with GET /workspaces/v1/msp-tenants] [API] Initial device discovery: GET /network-monitoring/v1/devices [the tasker builds the ver from these calls; an MSP login first lists tenants with GET /workspaces/v1/msp-tenants] [API] Initial device discovery: show system [CLI] L3 Interfaces: POST /network-troubleshooting/v1/cx//showCommands [the VLAN endpoint reports one primary IPv4 per VLAN, so the running-config supplies secondaries, loopbacks, IPv6 and mgmt] [API] IGMP Snooping: show ip igmp snooping detail [CLI] IGMP: show running-config [CLI] IGMP: show ip igmp groups all-vrfs [CLI] IGMP: show ip igmp all-vrfs [CLI] MAC: GET /network-monitoring/v1/switches//vlans [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [API] MAC: GET /network-monitoring/v1/switches//lag [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [API] MAC: GET /network-monitoring/v1/switches//interfaces [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [API] MAC: POST /network-troubleshooting/v1/cx//showCommands [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [API] MAC: show running-config [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [API] MAC: show interface [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [API] MAC: show ip interface brief [CLI] MAC: show interface vxlan vni [CLI] MAC: show interface vxlan vteps detail [CLI] MAC: show mac-address-table [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [CLI, API] L3 Interfaces: GET /network-monitoring/v1/switches//vlans [the VLAN endpoint reports one primary IPv4 per VLAN, so the running-config supplies secondaries, loopbacks, IPv6 and mgmt] [API] Disable pagination: no page [CLI] L3 Interfaces: show running-config [the VLAN endpoint reports one primary IPv4 per VLAN, so the running-config supplies secondaries, loopbacks, IPv6 and mgmt] [API] L3 Interfaces: show vrrp [CLI] L3 Interfaces: show interface mgmt [CLI] L3 Interfaces: show ip interface all-vrfs [CLI] L3 Interfaces: show ip interface [CLI] L3 Interfaces: show interface [CLI] L2 Interfaces: GET /network-monitoring/v1/switches//vlans [physical ports and LAGs from the API, VLAN interfaces, loopbacks, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [API] L2 Interfaces: GET /network-monitoring/v1/switches//lag [physical ports and LAGs from the API, VLAN interfaces, loopbacks, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [API] L2 Interfaces: GET /network-monitoring/v1/switches//interfaces [physical ports and LAGs from the API, VLAN interfaces, loopbacks, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [API] L2 Interfaces: POST /network-troubleshooting/v1/cx//showCommands [physical ports and LAGs from the API, VLAN interfaces, loopbacks, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [API] L2 Interfaces: show running-config [physical ports and LAGs from the API, VLAN interfaces, loopbacks, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [API] L2 Interfaces: show interface mgmt [CLI] L2 Interfaces: show interface [physical ports and LAGs from the API, VLAN interfaces, loopbacks, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [CLI, API] FHRP: show interface [CLI] FHRP: show vrrp [CLI] Task Support: -------------------------------------------------- Basic discovery: ✓ ARP [CLI, API] ✓ Device info [CLI, API] ✓ Disable pagination [CLI] ✓ FHRP (IPv6: ✗) [CLI, API ✗] ✓ Initial device discovery [CLI, API] ✓ IPv6 Neighbor Discovery (IPv6: ✓) [CLI ✗, API] ✓ L2 Interfaces [CLI, API] ✓ L3 Interfaces (IPv6: ✓) [CLI, API] ✓ Link aggregations [CLI, API] ✓ MAC [CLI, API] ✓ Neighbors (IPv6: ✗) [CLI, API ✗] ✓ Routing table (IPv6: ✗) [CLI, API] ○ Serial ports ✓ SN [CLI, API] ✓ STP [CLI, API] ✗ Virtual Contexts ✓ Vlan [CLI, API] Configuration: ✓ Configuration saved [CLI, API ✗] ✓ Current config [CLI, API] ✓ Startup config [CLI, API ✗] Hardware: ✗ Cluster ✓ End of Life data [CLI, API] ✗ Extenders ✗ PoE ✓ Power supplies & fans [CLI, API ✗] ✓ Stacking [CLI, API ✗] ✓ Transceivers [CLI, API ✗] ✗ VSS Hybrid discovery: ○ snCheck Management: ✓ DHCPv4 Relays (IPv6: ✗) [CLI, API ✗] ✗ DHCPv4 Servers (IPv6: ✗) ✓ DNS resolver (IPv6: ✗) [CLI, API ✗] ✗ IP Flow (IPv6: ✗) ○ License ✓ NTP (IPv6: ✗) [CLI, API ✗] ✗ Port mirroring ✗ PTP (IPv6: ✗) ✓ SNMP (IPv6: ✗) [CLI, API ✗] ✓ Syslog (IPv6: ✗) [CLI, API ✗] ✗ Unidirectional Link Detection MPLS: ○ Circuit cross-connect ✗ MPLS forwarding ✗ MPLS LDP ○ RSVP ○ VPLS ○ VPWS Multicast: ✓ IGMP [CLI, API ✗] ✓ IGMP Snooping [CLI, API ✗] ✗ MAC multicast address table ✓ MROUTE [CLI, API ✗] ✓ PIM [CLI, API ✗] Other: ○ Cloud network interfaces (IPv6: ○) ✗ PPPoE (IPv6: ✗) Policy: ✗ NAT44 QoS: ✗ QoS Routing: ○ BGP Advertised Routes (IPv6: ○) ○ Fabric Path ✓ Policy-based Routing (IPv6: ✗) [CLI, API ✗] ✓ Route summary (IPv6: ✗) [CLI, API ✗] ○ Routing policies ✓ VRF [CLI, API ✗] Routing protocols: ✓ BGP neighbors (IPv6: ✗) [CLI, API ✗] ○ EIGRP (IPv6: ○) ✗ IS-IS (IPv6: ✗) ○ Lisp (IPv6: ○) ✓ OSPF [CLI, API ✗] ✗ OSPFv3 (IPv6: ✗) ○ RIP SDN: ○ APIC (IPv6: ○) ○ Cisco ACI (IPv6: ○) ○ Virtual machines ✓ VXLAN [CLI, API ✗] SDWAN: ○ SD-WAN sites Security: ✓ AAA (IPv6: ✗) [CLI, API ✗] ✓ ACL (IPv6: ✗) [CLI, API ✗] ✗ DHCPv4 Snooping (IPv6: ✗) ✗ DMVPN (IPv6: ✗) ✗ Error disabled interfaces ✗ IPsec (IPv6: ✗) ○ LSVPN (IPv6: ○) ✗ Prefix lists (IPv6: ✗) ✓ Secured access ports [CLI, API ✗] ✗ Storm control ✗ STP port security ○ Virtual servers (IPv6: ○) ○ Zone firewall (IPv6: ○) Wireless: ○ Wireless AP ✗ Wireless clients ✗ Wireless Controller with APs All Families from hpe: -------------------------------------------------- hpe@comware hpe@aruba hpe@arubasw hpe@arubacx <-- current hpe@3com hpe@aruba-iap Legend: ✓=Full, ✗=Not Yet, ○=N/A Transport: [CLI] = SSH or Telnet session, [API] = vendor or controller API, ✗ after one = not yet integrated over it