# Family: hpe arubacx — v8.2.0

**Version:** 8.2.0
**Vendor:** hpe
**Family:** arubacx
**New in this version:** No
**Transport:** CLI, API
**URL:** https://matrix.ipfabric.io/8.2.0/family/200121839

---

## Commands

| Task | Command | Notes | Transport |
|------|---------|-------|-----------|
| OSPF | `show ip ospf all-vrfs` |  | CLI |
| Routing table | `show ip route` | Aruba New Central, over the showCommands runner. show ip route is the fallback when all-vrfs is refused (refused itself on the CX-6200F; same fallback as the arp runner). show running-config supplies the mgmt default gateway; with the VLAN endpoint it is the l3Interfaces dependency that CEF entries are filtered against | CLI, API |
| Route summary | `show ip route summary` |  | CLI |
| Route summary | `show ip route summary all-vrfs` |  | CLI |
| Link aggregations | `GET /network-monitoring/v1/switches/<serial-number>/interfaces` | Aruba New Central. The LAG endpoint reports no protocol (type is null on LACP aggregates too), so poProto is empty; the channel state is derived - up when a member is up | API |
| Link aggregations | `GET /network-monitoring/v1/switches/<serial-number>/lag` | Aruba New Central. The LAG endpoint reports no protocol (type is null on LACP aggregates too), so poProto is empty; the channel state is derived - up when a member is up | API |
| Link aggregations | `show lacp interfaces multi-chassis` |  | CLI |
| Link aggregations | `show vsx status` |  | CLI |
| Link aggregations | `show vsx brief` |  | CLI |
| Link aggregations | `show interface` |  | CLI |
| Link aggregations | `show interface lag` |  | CLI |
| Policy-based Routing | `show running-config` |  | CLI |
| OSPF | `show ip ospf neighbors detail all-vrfs` |  | CLI |
| OSPF | `show ip ospf neighbors detail` |  | CLI |
| OSPF | `show ip ospf interface all-vrfs` |  | CLI |
| OSPF | `show ip ospf interface` |  | CLI |
| Routing table | `show ip route all-vrfs` | Aruba New Central, over the showCommands runner. show ip route is the fallback when all-vrfs is refused (refused itself on the CX-6200F; same fallback as the arp runner). show running-config supplies the mgmt default gateway; with the VLAN endpoint it is the l3Interfaces dependency that CEF entries are filtered against | CLI, API |
| NTP | `show ntp associations` |  | CLI |
| Neighbors | `show cdp neighbor info <intName>` |  | CLI |
| Neighbors | `show cdp neighbor info` |  | CLI |
| Neighbors | `show lldp neighbor info <intName>` |  | CLI |
| Neighbors | `show lldp neighbor info` |  | CLI |
| IPv6 Neighbor Discovery | `GET /network-monitoring/v1/switches/<serial-number>/vlans` | Aruba New Central; both neighbor spellings run over the showCommands runner, the bare one as a fallback where the per-serial allow-list refuses all-vrfs. The VLAN endpoint and the running-config are read to keep only neighbours on an interface l3Interfaces also emits | API |
| IPv6 Neighbor Discovery | `POST /network-troubleshooting/v1/cx/<serial-number>/showCommands` | Aruba New Central; both neighbor spellings run over the showCommands runner, the bare one as a fallback where the per-serial allow-list refuses all-vrfs. The VLAN endpoint and the running-config are read to keep only neighbours on an interface l3Interfaces also emits | API |
| IPv6 Neighbor Discovery | `show running-config` | Aruba New Central; both neighbor spellings run over the showCommands runner, the bare one as a fallback where the per-serial allow-list refuses all-vrfs. The VLAN endpoint and the running-config are read to keep only neighbours on an interface l3Interfaces also emits | API |
| IPv6 Neighbor Discovery | `show ipv6 neighbors` | Aruba New Central; both neighbor spellings run over the showCommands runner, the bare one as a fallback where the per-serial allow-list refuses all-vrfs. The VLAN endpoint and the running-config are read to keep only neighbours on an interface l3Interfaces also emits | API |
| IPv6 Neighbor Discovery | `show ipv6 neighbors all-vrfs` | Aruba New Central; both neighbor spellings run over the showCommands runner, the bare one as a fallback where the per-serial allow-list refuses all-vrfs. The VLAN endpoint and the running-config are read to keep only neighbours on an interface l3Interfaces also emits | API |
| PIM | `show ip pim bsr all-vrfs` |  | CLI |
| PIM | `show ip pim neighbor all-vrfs` |  | CLI |
| PIM | `show ip pim rp-set all-vrfs` |  | CLI |
| PIM | `show ip pim interface all-vrfs` |  | CLI |
| MROUTE | `show ip mroute all-vrfs` |  | CLI |
| Stacking | `show vsf detail` |  | CLI |
| VXLAN | `show ip interface all-vrfs` |  | CLI |
| VXLAN | `show ip interface` |  | CLI |
| VXLAN | `show interface vxlan vni` |  | CLI |
| VXLAN | `show interface vxlan vteps detail` |  | CLI |
| VRF | `show vrf` |  | CLI |
| Vlan | `GET /network-monitoring/v1/switches/<serial-number>/vlans` | Aruba New Central; id, name and operational status | API |
| Vlan | `show vlan` |  | CLI |
| Transceivers | `show interface transceiver detail` |  | CLI |
| Syslog | `show running-config` |  | CLI |
| STP | `POST /network-troubleshooting/v1/cx/<serial-number>/showCommands` | Aruba New Central. RPVST root cost comes only from show spanning-tree summary root, refused by the lab CX-6200F allow-list | API |
| STP | `show vlan` | Aruba New Central. RPVST root cost comes only from show spanning-tree summary root, refused by the lab CX-6200F allow-list | CLI, API |
| STP | `show spanning-tree summary root` | Aruba New Central. RPVST root cost comes only from show spanning-tree summary root, refused by the lab CX-6200F allow-list | CLI, API |
| STP | `show spanning-tree mst detail` | Aruba New Central. RPVST root cost comes only from show spanning-tree summary root, refused by the lab CX-6200F allow-list | CLI, API |
| STP | `show spanning-tree detail` | Aruba New Central. RPVST root cost comes only from show spanning-tree summary root, refused by the lab CX-6200F allow-list | CLI, API |
| Stacking | `show vsf link` |  | CLI |
| IGMP Snooping | `show ip igmp snooping` |  | CLI |
| SNMP | `show running-config` |  | CLI |
| SN | `show system` |  | CLI |
| SN | `GET /network-monitoring/v1/devices` | the tasker builds the ver from this call; the task sends no request of its own | API |
| Secured access ports | `show port-access clients detail` |  | CLI |
| Routing table | `GET /network-monitoring/v1/switches/<serial-number>/vlans` | Aruba New Central, over the showCommands runner. show ip route is the fallback when all-vrfs is refused (refused itself on the CX-6200F; same fallback as the arp runner). show running-config supplies the mgmt default gateway; with the VLAN endpoint it is the l3Interfaces dependency that CEF entries are filtered against | API |
| Routing table | `POST /network-troubleshooting/v1/cx/<serial-number>/showCommands` | Aruba New Central, over the showCommands runner. show ip route is the fallback when all-vrfs is refused (refused itself on the CX-6200F; same fallback as the arp runner). show running-config supplies the mgmt default gateway; with the VLAN endpoint it is the l3Interfaces dependency that CEF entries are filtered against | API |
| Routing table | `show running-config` | Aruba New Central, over the showCommands runner. show ip route is the fallback when all-vrfs is refused (refused itself on the CX-6200F; same fallback as the arp runner). show running-config supplies the mgmt default gateway; with the VLAN endpoint it is the l3Interfaces dependency that CEF entries are filtered against | API |
| Routing table | `show ip interface brief` |  | CLI |
| Routing table | `show interface vxlan vni` |  | CLI |
| Routing table | `show interface vxlan vteps detail` |  | CLI |
| Routing table | `show interface mgmt` |  | CLI |
| Routing table | `show ip route <protocolName>` |  | CLI |
| Routing table | `show ip route <protocolName> all-vrfs` |  | CLI |
| Routing table | `show ip route summary` |  | CLI |
| Routing table | `show ip route summary all-vrfs` |  | CLI |
| Device info | `GET /network-monitoring/v1/devices` | the tasker builds the ver from this call; the task sends no request of its own | API |
| Power supplies & fans | `show environment` |  | CLI |
| DNS resolver | `show ip dns` |  | CLI |
| DHCPv4 Relays | `show dhcp-relay` |  | CLI |
| DHCPv4 Relays | `show ip helper-address` |  | CLI |
| Startup config | `show startup-config` |  | CLI |
| Current config | `POST /network-troubleshooting/v1/cx/<serial-number>/showCommands` |  | API |
| Current config | `show running-config` |  | CLI, API |
| Configuration saved | `show running-config` |  | CLI |
| Configuration saved | `show startup-config` |  | CLI |
| Device info | `show boot-history` |  | CLI |
| Device info | `show images` |  | CLI |
| Device info | `show lldp local-device` |  | CLI |
| Device info | `show module` |  | CLI |
| Device info | `show system` |  | CLI |
| Device info | `top memory` |  | CLI |
| Power supplies & fans | `show system` |  | CLI |
| BGP neighbors | `show bpg all neighbors` |  | CLI |
| BGP neighbors | `show bgp all-vrf all neighbors` |  | CLI |
| ARP | `GET /network-monitoring/v1/switches/<serial-number>/vlans` | Aruba New Central; both spellings run over the showCommands runner, the bare one as a fallback where the device rejects all-vrfs. The running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only entries on an interface it emits | API |
| ARP | `POST /network-troubleshooting/v1/cx/<serial-number>/showCommands` | Aruba New Central; both spellings run over the showCommands runner, the bare one as a fallback where the device rejects all-vrfs. The running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only entries on an interface it emits | API |
| ARP | `show running-config` | Aruba New Central; both spellings run over the showCommands runner, the bare one as a fallback where the device rejects all-vrfs. The running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only entries on an interface it emits | API |
| ARP | `show arp` | Aruba New Central; both spellings run over the showCommands runner, the bare one as a fallback where the device rejects all-vrfs. The running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only entries on an interface it emits | CLI, API |
| ARP | `show arp all-vrfs` | Aruba New Central; both spellings run over the showCommands runner, the bare one as a fallback where the device rejects all-vrfs. The running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only entries on an interface it emits | CLI, API |
| ACL | `show running-config` |  | CLI |
| AAA | `show aaa server-groups` |  | CLI |
| AAA | `show aaa authorization` |  | CLI |
| AAA | `show aaa authentication` |  | CLI |
| AAA | `show aaa accounting` |  | CLI |
| Initial device discovery | `GET /network-monitoring/v1/switches` | the tasker builds the ver from these calls; an MSP login first lists tenants with GET /workspaces/v1/msp-tenants | API |
| Initial device discovery | `GET /network-monitoring/v1/devices` | the tasker builds the ver from these calls; an MSP login first lists tenants with GET /workspaces/v1/msp-tenants | API |
| Initial device discovery | `show system` |  | CLI |
| L3 Interfaces | `POST /network-troubleshooting/v1/cx/<serial-number>/showCommands` | the VLAN endpoint reports one primary IPv4 per VLAN, so the running-config supplies secondaries, loopbacks, IPv6 and mgmt | API |
| IGMP Snooping | `show ip igmp snooping detail` |  | CLI |
| IGMP | `show running-config` |  | CLI |
| IGMP | `show ip igmp groups all-vrfs` |  | CLI |
| IGMP | `show ip igmp all-vrfs` |  | CLI |
| MAC | `GET /network-monitoring/v1/switches/<serial-number>/vlans` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| MAC | `GET /network-monitoring/v1/switches/<serial-number>/lag` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| MAC | `GET /network-monitoring/v1/switches/<serial-number>/interfaces` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| MAC | `POST /network-troubleshooting/v1/cx/<serial-number>/showCommands` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| MAC | `show running-config` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| MAC | `show interface` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| MAC | `show ip interface brief` |  | CLI |
| MAC | `show interface vxlan vni` |  | CLI |
| MAC | `show interface vxlan vteps detail` |  | CLI |
| MAC | `show mac-address-table` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | CLI, API |
| L3 Interfaces | `GET /network-monitoring/v1/switches/<serial-number>/vlans` | the VLAN endpoint reports one primary IPv4 per VLAN, so the running-config supplies secondaries, loopbacks, IPv6 and mgmt | API |
| Disable pagination | `no page` |  | CLI |
| L3 Interfaces | `show running-config` | the VLAN endpoint reports one primary IPv4 per VLAN, so the running-config supplies secondaries, loopbacks, IPv6 and mgmt | API |
| L3 Interfaces | `show vrrp` |  | CLI |
| L3 Interfaces | `show interface mgmt` |  | CLI |
| L3 Interfaces | `show ip interface all-vrfs` |  | CLI |
| L3 Interfaces | `show ip interface` |  | CLI |
| L3 Interfaces | `show interface` |  | CLI |
| L2 Interfaces | `GET /network-monitoring/v1/switches/<serial-number>/vlans` | physical ports and LAGs from the API, VLAN interfaces, loopbacks, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown | API |
| L2 Interfaces | `GET /network-monitoring/v1/switches/<serial-number>/lag` | physical ports and LAGs from the API, VLAN interfaces, loopbacks, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown | API |
| L2 Interfaces | `GET /network-monitoring/v1/switches/<serial-number>/interfaces` | physical ports and LAGs from the API, VLAN interfaces, loopbacks, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown | API |
| L2 Interfaces | `POST /network-troubleshooting/v1/cx/<serial-number>/showCommands` | physical ports and LAGs from the API, VLAN interfaces, loopbacks, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown | API |
| L2 Interfaces | `show running-config` | physical ports and LAGs from the API, VLAN interfaces, loopbacks, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown | API |
| L2 Interfaces | `show interface mgmt` |  | CLI |
| L2 Interfaces | `show interface` | physical ports and LAGs from the API, VLAN interfaces, loopbacks, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown | CLI, API |
| FHRP | `show interface` |  | CLI |
| FHRP | `show vrrp` |  | CLI |

---

## Supported Tasks

| Category | Task | Status | IPv6 | Notes | Transport |
|----------|------|--------|------|-------|-----------|
| Basic discovery | ARP | ✓ | — | API: Aruba New Central, over the showCommands runner - no API endpoint carries ARP. Only entries on an interface l3Interfaces emits are kept. CX reads all-vrfs, which omits the mgmt VRF, and its allow-list refuses show arp vrf <name>. The AOS-S oobm ARP table is not read. aruba-iap has no L3 interface source, so it stays n/a | CLI, API |
| Basic discovery | Device info | ✓ | — |  | CLI, API |
| Basic discovery | Disable pagination | ✓ | — |  | CLI |
| Basic discovery | FHRP | ✓ | ✗ |  | CLI, API ✗ |
| Basic discovery | Initial device discovery | ✓ | — | API: family, model and version come from the tasker device list | CLI, API |
| Basic discovery | IPv6 Neighbor Discovery | ✓ | ✓ | API: Aruba New Central; only neighbours on an interface l3Interfaces emits: VLAN SVIs from the switch VLAN endpoint plus every addressed interface in `show running-config` | CLI ✗, API |
| Basic discovery | L2 Interfaces | ✓ | — | API: switches add VLAN interfaces, loopbacks and per-port MACs from the CLI-over-API runner; gateways add their VLAN interfaces as name-only rows in state unknown; APs are wired ports only | CLI, API |
| Basic discovery | L3 Interfaces | ✓ | ✓ | API: Aruba New Central; secondaries, loopbacks, IPv6 and mgmt (in `__oob-management`) from `show running-config`; every other interface in the native VRF (`vrf attach` is not parsed yet) | CLI, API |
| Basic discovery | Link aggregations | ✓ | — | API: Aruba New Central switches. Port channels and members only - no protocol and no MLAG/VSX source in the API | CLI, API |
| Basic discovery | MAC | ✓ | — | API: Aruba New Central, over the showCommands runner - no API endpoint carries the MAC table. Only entries on an interface l2Interfaces emits are kept. CX VXLAN entries keep their VTEP but carry no VNI, the vxlan task has no API path. Gateway rows carry no source, and gateway rows on a port-channel or tunnel are not read. AOS-S has no per-VLAN fallback. aruba-iap stays n/a | CLI, API |
| Basic discovery | Neighbors | ✓ | ✗ |  | CLI, API ✗ |
| Basic discovery | Routing table | ✓ | ✗ | API: Aruba New Central, over the showCommands runner. No IPv6 (show ipv6 route refused), no full-BGP limit (show ip route summary refused), no VXLAN next hops (the vxlan task has no API path). A reply without the Total Route Count footer is reported as possibly truncated | CLI, API |
| Basic discovery | Serial ports | ○ | — |  | — |
| Basic discovery | SN | ✓ | — |  | CLI, API |
| Basic discovery | STP | ✓ | — | API: Aruba New Central. RPVST publishes no rows and one error, and the task does not fail, where the device refuses show spanning-tree summary root | CLI, API |
| Basic discovery | Virtual Contexts | ✗ | — |  | — |
| Basic discovery | Vlan | ✓ | — | API: Aruba New Central; id, name and operational status on every family, the gateway name coming from `show vlan` rather than the API. `dscr` is on no endpoint, and aruba-iap has no VLAN source at all, so it stays n/a | CLI, API |
| Configuration | Configuration saved | ✓ | — | API: runs over the API but always publishes N/A: deviceConfig/startup does not run over the API | CLI, API ✗ |
| Configuration | Current config | ✓ | — |  | CLI, API |
| Configuration | Startup config | ✓ | — |  | CLI, API ✗ |
| Hardware | Cluster | ✗ | — |  | — |
| Hardware | End of Life data | ✓ | — | API: chassis part number only | CLI, API |
| Hardware | Extenders | ✗ | — |  | — |
| Hardware | PoE | ✗ | — |  | — |
| Hardware | Power supplies & fans | ✓ | — |  | CLI, API ✗ |
| Hardware | Stacking | ✓ | — |  | CLI, API ✗ |
| Hardware | Transceivers | ✓ | — |  | CLI, API ✗ |
| Hardware | VSS | ✗ | — |  | — |
| Hybrid discovery | snCheck | ○ | — |  | — |
| Management | DHCPv4 Relays | ✓ | ✗ |  | CLI, API ✗ |
| Management | DHCPv4 Servers | ✗ | ✗ |  | — |
| Management | DNS resolver | ✓ | ✗ |  | CLI, API ✗ |
| Management | IP Flow | ✗ | ✗ |  | — |
| Management | License | ○ | — |  | — |
| Management | NTP | ✓ | ✗ |  | CLI, API ✗ |
| Management | Port mirroring | ✗ | — |  | — |
| Management | PTP | ✗ | ✗ |  | — |
| Management | SNMP | ✓ | ✗ |  | CLI, API ✗ |
| Management | Syslog | ✓ | ✗ |  | CLI, API ✗ |
| Management | Unidirectional Link Detection | ✗ | — |  | — |
| MPLS | Circuit cross-connect | ○ | — |  | — |
| MPLS | MPLS forwarding | ✗ | — |  | — |
| MPLS | MPLS LDP | ✗ | — |  | — |
| MPLS | RSVP | ○ | — |  | — |
| MPLS | VPLS | ○ | — |  | — |
| MPLS | VPWS | ○ | — |  | — |
| Multicast | IGMP | ✓ | — |  | CLI, API ✗ |
| Multicast | IGMP Snooping | ✓ | — |  | CLI, API ✗ |
| Multicast | MAC multicast address table | ✗ | — |  | — |
| Multicast | MROUTE | ✓ | — |  | CLI, API ✗ |
| Multicast | PIM | ✓ | — |  | CLI, API ✗ |
| Other | Cloud network interfaces | ○ | ○ |  | — |
| Other | PPPoE | ✗ | ✗ |  | — |
| Policy | NAT44 | ✗ | — |  | — |
| QoS | QoS | ✗ | — |  | — |
| Routing | BGP Advertised Routes | ○ | ○ |  | — |
| Routing | Fabric Path | ○ | — |  | — |
| Routing | Policy-based Routing | ✓ | ✗ |  | CLI, API ✗ |
| Routing | Route summary | ✓ | ✗ |  | CLI, API ✗ |
| Routing | Routing policies | ○ | — |  | — |
| Routing | VRF | ✓ | — |  | CLI, API ✗ |
| Routing protocols | BGP neighbors | ✓ | ✗ |  | CLI, API ✗ |
| Routing protocols | EIGRP | ○ | ○ |  | — |
| Routing protocols | IS-IS | ✗ | ✗ |  | — |
| Routing protocols | Lisp | ○ | ○ |  | — |
| Routing protocols | OSPF | ✓ | — |  | CLI, API ✗ |
| Routing protocols | OSPFv3 | ✗ | ✗ |  | — |
| Routing protocols | RIP | ○ | — |  | — |
| SDN | APIC | ○ | ○ |  | — |
| SDN | Cisco ACI | ○ | ○ |  | — |
| SDN | Virtual machines | ○ | — |  | — |
| SDN | VXLAN | ✓ | — |  | CLI, API ✗ |
| SDWAN | SD-WAN sites | ○ | — |  | — |
| Security | AAA | ✓ | ✗ |  | CLI, API ✗ |
| Security | ACL | ✓ | ✗ |  | CLI, API ✗ |
| Security | DHCPv4 Snooping | ✗ | ✗ |  | — |
| Security | DMVPN | ✗ | ✗ |  | — |
| Security | Error disabled interfaces | ✗ | — |  | — |
| Security | IPsec | ✗ | ✗ |  | — |
| Security | LSVPN | ○ | ○ |  | — |
| Security | Prefix lists | ✗ | ✗ |  | — |
| Security | Secured access ports | ✓ | — |  | CLI, API ✗ |
| Security | Storm control | ✗ | — |  | — |
| Security | STP port security | ✗ | — |  | — |
| Security | Virtual servers | ○ | ○ |  | — |
| Security | Zone firewall | ○ | ○ |  | — |
| Wireless | Wireless AP | ○ | — |  | — |
| Wireless | Wireless clients | ✗ | — |  | — |
| Wireless | Wireless Controller with APs | ✗ | — |  | — |

---

## All Families from hpe

- [hpe@comware](https://matrix.ipfabric.io/8.2.0/family/200121830)
- [hpe@aruba](https://matrix.ipfabric.io/8.2.0/family/200121833)
- [hpe@arubasw](https://matrix.ipfabric.io/8.2.0/family/200121836)
- **hpe@arubacx** *(current)*
- [hpe@3com](https://matrix.ipfabric.io/8.2.0/family/200121842)
- [hpe@aruba-iap](https://matrix.ipfabric.io/8.2.0/family/200121845)

---

## Legend

- **✓** = Fully Integrated
- **✗** = Not Yet Integrated
- **○** = Not Available
- **🆕** = New in this version
- **CLI** = SSH or Telnet session, **API** = vendor or controller API; in the Transport column, **✗** after one = not yet integrated over it, **—** = not integrated over any transport. A family reached over both may use the API together with CLI or instead of it.

*Generated: 2026-11-22T13:54:25.356Z*
