Family: hpe arubasw (v8.2.0) ================================================== Vendor: hpe Family: arubasw Transport: CLI, API New: No Commands: -------------------------------------------------- MAC: POST /network-troubleshooting/v1/aos-s//showCommands [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [API] Link aggregations: show interfaces brief [CLI] Link aggregations: show trunks [CLI] OSPF: show running-config [CLI] OSPF: show ip [CLI] OSPF: show ip ospf neighbor detail [CLI] OSPF: show ip ospf interface [CLI] OSPF: show ip ospf interface [CLI] NTP: show ntp associations [CLI] Neighbors: show lldp info remote-device [CLI] Neighbors: show lldp info remote-device [CLI] Neighbors: show lldp info remote-device detail [CLI] Neighbors: show cdp neighbors [CLI] MAC: GET /network-monitoring/v1/switches//vlans [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [API] MAC: GET /network-monitoring/v1/switches//lag [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [API] MAC: GET /network-monitoring/v1/switches//interfaces [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [API] Link aggregations: GET /network-monitoring/v1/switches//lag [Aruba New Central. The LAG endpoint reports no protocol (type is null on LACP aggregates too), so poProto is empty; the channel state is derived - up when a member is up] [API] MAC: show running-config [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [API] MAC: show oobm ip [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [API] MAC: show oobm [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [API] MAC: show lldp info local-device [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [API] MAC: show ip route [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [API] MAC: show ip [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [API] MAC: show interfaces all [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [API] MAC: show vlans [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [CLI, API] MAC: show mac-address vlan [CLI] MAC: show mac-address [Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits] [CLI, API] L3 Interfaces: GET /network-monitoring/v1/switches//vlans [the VLAN endpoint reports one primary IPv4 per VLAN, so the running-config supplies secondaries and loopbacks (IPv4 only)] [API] L3 Interfaces: POST /network-troubleshooting/v1/aos-s//showCommands [the VLAN endpoint reports one primary IPv4 per VLAN, so the running-config supplies secondaries and loopbacks (IPv4 only)] [API] L3 Interfaces: show running-config [the VLAN endpoint reports one primary IPv4 per VLAN, so the running-config supplies secondaries and loopbacks (IPv4 only)] [API] L3 Interfaces: show oobm ip [the VLAN endpoint reports one primary IPv4 per VLAN, so the running-config supplies secondaries and loopbacks (IPv4 only)] [CLI, API] STP: show spanning-tree [Aruba New Central. show spanning-tree vlan for every VLAN in RPVST mode; the instance commands only in MSTP mode] [CLI, API] Vlan: GET /network-monitoring/v1/switches//vlans [Aruba New Central; id, name and operational status] [API] Vlan: show vlans [CLI] Transceivers: show interfaces transceiver detail [CLI] Transceivers: show interfaces transceiver [CLI] Syslog: show syslog config [CLI] STP port security: show spanning-tree detail [CLI] STP: POST /network-troubleshooting/v1/aos-s//showCommands [Aruba New Central. show spanning-tree vlan for every VLAN in RPVST mode; the instance commands only in MSTP mode] [API] STP: show vlans ports all detail [Aruba New Central. show spanning-tree vlan for every VLAN in RPVST mode; the instance commands only in MSTP mode] [CLI, API] STP: show vlans [Aruba New Central. show spanning-tree vlan for every VLAN in RPVST mode; the instance commands only in MSTP mode] [CLI, API] STP: show spanning-tree debug-counters instance ports all [Aruba New Central. show spanning-tree vlan for every VLAN in RPVST mode; the instance commands only in MSTP mode] [CLI, API] STP: show spanning-tree instance [Aruba New Central. show spanning-tree vlan for every VLAN in RPVST mode; the instance commands only in MSTP mode] [CLI, API] STP: show spanning-tree detail [CLI] STP: show spanning-tree mst-config [Aruba New Central. show spanning-tree vlan for every VLAN in RPVST mode; the instance commands only in MSTP mode] [CLI, API] STP: show spanning-tree vlan [Aruba New Central. show spanning-tree vlan for every VLAN in RPVST mode; the instance commands only in MSTP mode] [CLI, API] STP: show spanning-tree config [Aruba New Central. show spanning-tree vlan for every VLAN in RPVST mode; the instance commands only in MSTP mode] [CLI, API] L3 Interfaces: show vrrp vlan vrid config [CLI] Stacking: show vsf link [CLI] Stacking: show vsf detail [CLI] Stacking: show stacking [CLI] SNMP: show running-configuration [CLI] SN: show system [CLI] SN: GET /network-monitoring/v1/devices [the tasker builds the ver from this call; the task sends no request of its own] [API] Routing table: GET /network-monitoring/v1/switches//vlans [Aruba New Central; the show commands run over the showCommands runner. show running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only CEF entries on an interface it emits] [API] Routing table: POST /network-troubleshooting/v1/aos-s//showCommands [Aruba New Central; the show commands run over the showCommands runner. show running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only CEF entries on an interface it emits] [API] Routing table: show running-config [Aruba New Central; the show commands run over the showCommands runner. show running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only CEF entries on an interface it emits] [API] Routing table: show ipv6 route [Aruba New Central; the show commands run over the showCommands runner. show running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only CEF entries on an interface it emits] [API] Routing table: show oobm ip [Aruba New Central; the show commands run over the showCommands runner. show running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only CEF entries on an interface it emits] [CLI, API] Routing table: show vlans [Aruba New Central; the show commands run over the showCommands runner. show running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only CEF entries on an interface it emits] [CLI, API] Routing table: show ip route [Aruba New Central; the show commands run over the showCommands runner. show running-config and the VLAN endpoint are l3Interfaces dependencies, read to keep only CEF entries on an interface it emits] [CLI, API] Link aggregations: GET /network-monitoring/v1/switches//interfaces [Aruba New Central. The LAG endpoint reports no protocol (type is null on LACP aggregates too), so poProto is empty; the channel state is derived - up when a member is up] [API] ARP: show oobm ip [Aruba New Central; one show arp vlan per SVI l3Interfaces emits, over the showCommands runner. The running-config, show oobm ip and the VLAN endpoint are its dependencies, read to keep only entries on an interface it emits] [API] Startup config: show config [CLI] Current config: POST /network-troubleshooting/v1/aos-s//showCommands [API] Current config: show running-config [CLI, API] Configuration saved: show running-config [CLI] Configuration saved: show config [CLI] Device info: show lldp info local-device [the members of a 5400R chassis are collected by "show vsf detail", the rest of the family uses "show stacking"] [CLI] Device info: show vsf detail [the members of a 5400R chassis are collected by "show vsf detail", the rest of the family uses "show stacking"] [CLI] Device info: show stacking [the members of a 5400R chassis are collected by "show vsf detail", the rest of the family uses "show stacking"] [CLI] Device info: show console [the members of a 5400R chassis are collected by "show vsf detail", the rest of the family uses "show stacking"] [CLI] Device info: show tech buffer [the members of a 5400R chassis are collected by "show vsf detail", the rest of the family uses "show stacking"] [CLI] Device info: show modules [the members of a 5400R chassis are collected by "show vsf detail", the rest of the family uses "show stacking"] [CLI] Device info: show system [the members of a 5400R chassis are collected by "show vsf detail", the rest of the family uses "show stacking"] [CLI] Device info: GET /network-monitoring/v1/devices [the tasker builds the ver from this call; the task sends no request of its own] [API] ARP: GET /network-monitoring/v1/switches//vlans [Aruba New Central; one show arp vlan per SVI l3Interfaces emits, over the showCommands runner. The running-config, show oobm ip and the VLAN endpoint are its dependencies, read to keep only entries on an interface it emits] [API] ARP: POST /network-troubleshooting/v1/aos-s//showCommands [Aruba New Central; one show arp vlan per SVI l3Interfaces emits, over the showCommands runner. The running-config, show oobm ip and the VLAN endpoint are its dependencies, read to keep only entries on an interface it emits] [API] DHCPv4 Relays: show ip helper-address [CLI] ARP: show arp vlan [Aruba New Central; one show arp vlan per SVI l3Interfaces emits, over the showCommands runner. The running-config, show oobm ip and the VLAN endpoint are its dependencies, read to keep only entries on an interface it emits] [API] ARP: show vlans [CLI] ARP: show running-config [Aruba New Central; one show arp vlan per SVI l3Interfaces emits, over the showCommands runner. The running-config, show oobm ip and the VLAN endpoint are its dependencies, read to keep only entries on an interface it emits] [CLI, API] ARP: show mac-address vlan [CLI] ARP: show ip [CLI] ARP: show arp [CLI] AAA: show password-configuration [CLI] Initial device discovery: GET /network-monitoring/v1/switches [the tasker builds the ver from these calls; an MSP login first lists tenants with GET /workspaces/v1/msp-tenants] [API] Initial device discovery: GET /network-monitoring/v1/devices [the tasker builds the ver from these calls; an MSP login first lists tenants with GET /workspaces/v1/msp-tenants] [API] Initial device discovery: show lldp info local-device [CLI] Initial device discovery: show tech buffers [CLI] Initial device discovery: show modules [CLI] Initial device discovery: show stacking [CLI] Initial device discovery: show version [CLI] L2 Interfaces: show run [CLI] L3 Interfaces: show vrrp [CLI] L3 Interfaces: show vlans [CLI] L3 Interfaces: show ip [CLI] L3 Interfaces: show run [CLI] L2 Interfaces: GET /network-monitoring/v1/switches//vlans [physical ports and LAGs from the API, VLAN interfaces, loopbacks, oobm, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [API] L2 Interfaces: GET /network-monitoring/v1/switches//lag [physical ports and LAGs from the API, VLAN interfaces, loopbacks, oobm, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [API] L2 Interfaces: GET /network-monitoring/v1/switches//interfaces [physical ports and LAGs from the API, VLAN interfaces, loopbacks, oobm, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [API] L2 Interfaces: POST /network-troubleshooting/v1/aos-s//showCommands [physical ports and LAGs from the API, VLAN interfaces, loopbacks, oobm, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [API] L2 Interfaces: show running-config [physical ports and LAGs from the API, VLAN interfaces, loopbacks, oobm, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [API] L2 Interfaces: show oobm ip [physical ports and LAGs from the API, VLAN interfaces, loopbacks, oobm, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [API] L2 Interfaces: show ip route [physical ports and LAGs from the API, VLAN interfaces, loopbacks, oobm, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [API] L2 Interfaces: show oobm [physical ports and LAGs from the API, VLAN interfaces, loopbacks, oobm, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [CLI, API] L2 Interfaces: show lldp info local-device [physical ports and LAGs from the API, VLAN interfaces, loopbacks, oobm, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [CLI, API] L2 Interfaces: show ip [physical ports and LAGs from the API, VLAN interfaces, loopbacks, oobm, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [CLI, API] Disable pagination: no page [CLI] L2 Interfaces: show vlans [CLI] L2 Interfaces: show vlans [physical ports and LAGs from the API, VLAN interfaces, loopbacks, oobm, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [CLI, API] L2 Interfaces: show vlans ports all detail [CLI] L2 Interfaces: show interfaces brief [CLI] L2 Interfaces: show interfaces all [physical ports and LAGs from the API, VLAN interfaces, loopbacks, oobm, per-port MACs and counters from the CLI; any other l3Interfaces row gets a name-only row in state unknown] [CLI, API] FHRP: show ip [CLI] FHRP: show run [CLI] FHRP: show vrrp vlan vrid config [CLI] FHRP: show vrrp [CLI] DNS resolver: show ip dns [CLI] DHCPv4 Snooping: show dhcp-snooping stats [CLI] DHCPv4 Snooping: show dhcp-snooping binding [CLI] DHCPv4 Snooping: show dhcp-snooping [CLI] DHCPv4 Relays: show dhcp-relay [CLI] Task Support: -------------------------------------------------- Basic discovery: ✓ ARP [CLI, API] ✓ Device info [CLI, API] ✓ Disable pagination [CLI] ✓ FHRP (IPv6: ✗) [CLI, API ✗] ✓ Initial device discovery [CLI, API] ✗ IPv6 Neighbor Discovery (IPv6: ✗) ✓ L2 Interfaces [CLI, API] ✓ L3 Interfaces (IPv6: ✗) [CLI, API] ✓ Link aggregations [CLI, API] ✓ MAC [CLI, API] ✓ Neighbors (IPv6: ✗) [CLI, API ✗] ✓ Routing table (IPv6: ✓) [CLI, API] ○ Serial ports ✓ SN [CLI, API] ✓ STP [CLI, API] ○ Virtual Contexts ✓ Vlan [CLI, API] Configuration: ✓ Configuration saved [CLI, API ✗] ✓ Current config [CLI, API] ✓ Startup config [CLI, API ✗] Hardware: ○ Cluster ✓ End of Life data [CLI, API] ○ Extenders ✗ PoE ✗ Power supplies & fans ✓ Stacking [CLI, API ✗] ✓ Transceivers [CLI, API ✗] ○ VSS Hybrid discovery: ○ snCheck Management: ✓ DHCPv4 Relays (IPv6: ✗) [CLI, API ✗] ✗ DHCPv4 Servers (IPv6: ✗) ✓ DNS resolver (IPv6: ✗) [CLI, API ✗] ○ IP Flow (IPv6: ○) ○ License ✓ NTP (IPv6: ✗) [CLI, API ✗] ✗ Port mirroring ✗ PTP (IPv6: ✗) ✓ SNMP (IPv6: ✗) [CLI, API ✗] ✓ Syslog (IPv6: ✗) [CLI, API ✗] ✗ Unidirectional Link Detection MPLS: ○ Circuit cross-connect ○ MPLS forwarding ○ MPLS LDP ✗ RSVP ○ VPLS ○ VPWS Multicast: ✗ IGMP ✗ IGMP Snooping ○ MAC multicast address table ✗ MROUTE ✗ PIM Other: ○ Cloud network interfaces (IPv6: ○) ✗ PPPoE (IPv6: ✗) Policy: ✗ NAT44 QoS: ✗ QoS Routing: ○ BGP Advertised Routes (IPv6: ○) ○ Fabric Path ○ Policy-based Routing (IPv6: ○) ✗ Route summary (IPv6: ✗) ○ Routing policies ○ VRF Routing protocols: ○ BGP neighbors (IPv6: ○) ○ EIGRP (IPv6: ○) ○ IS-IS (IPv6: ○) ○ Lisp (IPv6: ○) ✓ OSPF [CLI, API ✗] ✗ OSPFv3 (IPv6: ✗) ○ RIP SDN: ○ APIC (IPv6: ○) ○ Cisco ACI (IPv6: ○) ○ Virtual machines ✗ VXLAN SDWAN: ○ SD-WAN sites Security: ✗ AAA (IPv6: ✗) ✗ ACL (IPv6: ✗) ✓ DHCPv4 Snooping (IPv6: ✗) [CLI, API ✗] ○ DMVPN (IPv6: ○) ✗ Error disabled interfaces ○ IPsec (IPv6: ○) ○ LSVPN (IPv6: ○) ○ Prefix lists (IPv6: ○) ✗ Secured access ports ✗ Storm control ✓ STP port security [CLI, API ✗] ○ Virtual servers (IPv6: ○) ○ Zone firewall (IPv6: ○) Wireless: ○ Wireless AP ○ Wireless clients ○ Wireless Controller with APs All Families from hpe: -------------------------------------------------- hpe@comware hpe@aruba hpe@arubasw <-- current hpe@arubacx hpe@3com hpe@aruba-iap Legend: ✓=Full, ✗=Not Yet, ○=N/A Transport: [CLI] = SSH or Telnet session, [API] = vendor or controller API, ✗ after one = not yet integrated over it