# Family: hpe aruba — v8.2.0

**Version:** 8.2.0
**Vendor:** hpe
**Family:** aruba
**New in this version:** No
**Transport:** CLI, API
**URL:** https://matrix.ipfabric.io/8.2.0/family/200121833

---

## Commands

| Task | Command | Notes | Transport |
|------|---------|-------|-----------|
| Neighbors | `show lldp neighbor` |  | CLI |
| SN | `show inventory` |  | CLI |
| SN | `GET /network-monitoring/v1/devices` | the tasker builds the ver from this call; the task sends no request of its own | API |
| Routing table | `GET /network-monitoring/v1/gateways/<serial-number>/vlans` | Aruba New Central; show ip route runs over the showCommands runner. The VLAN endpoint is an l3Interfaces dependency, read to keep only CEF entries on an interface it emits | API |
| Routing table | `POST /network-troubleshooting/v1/gateways/<serial-number>/showCommands` | Aruba New Central; show ip route runs over the showCommands runner. The VLAN endpoint is an l3Interfaces dependency, read to keep only CEF entries on an interface it emits | API |
| Routing table | `show ip route` | Aruba New Central; show ip route runs over the showCommands runner. The VLAN endpoint is an l3Interfaces dependency, read to keep only CEF entries on an interface it emits | API |
| Link aggregations | `show interface <intName>` |  | CLI |
| Link aggregations | `show vlan status` |  | CLI |
| Link aggregations | `show port stats` |  | CLI |
| NTP | `show ntp servers` |  | CLI |
| Neighbors | `show lldp neighbor interface <intName> detail` |  | CLI |
| SNMP | `show running-configuration` |  | CLI |
| IPv6 Neighbor Discovery | `GET /network-monitoring/v1/gateways/<serial-number>/vlans` | Aruba New Central; the show command runs over the showCommands runner. The VLAN endpoint is read to keep only neighbours on an interface l3Interfaces also emits | API |
| IPv6 Neighbor Discovery | `POST /network-troubleshooting/v1/gateways/<serial-number>/showCommands` | Aruba New Central; the show command runs over the showCommands runner. The VLAN endpoint is read to keep only neighbours on an interface l3Interfaces also emits | API |
| IPv6 Neighbor Discovery | `show ipv6 neighbors` | Aruba New Central; the show command runs over the showCommands runner. The VLAN endpoint is read to keep only neighbours on an interface l3Interfaces also emits | API |
| MAC | `GET /network-monitoring/v1/gateways/<serial-number>/vlans` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| MAC | `GET /network-monitoring/v1/gateways/<serial-number>/ports` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| MAC | `POST /network-troubleshooting/v1/gateways/<serial-number>/showCommands` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | API |
| MAC | `show datapath bridge` | Aruba New Central; the show command runs over the showCommands runner. The other commands are l2Interfaces dependencies, read to keep only entries on an interface it emits | CLI, API |
| L3 Interfaces | `GET /network-monitoring/v1/gateways/<serial-number>/vlans` |  | API |
| L3 Interfaces | `show ip interface brief` |  | CLI |
| Wireless clients | `show ap association client-mac <clientMac>` |  | CLI |
| Wireless Controller with APs | `show ip interface brief` |  | CLI |
| Wireless Controller with APs | `show ap bss-table` |  | CLI |
| Wireless Controller with APs | `show ap debug lacp ap-name <apName>` |  | CLI |
| Wireless Controller with APs | `show ap lldp neighbors` |  | CLI |
| Wireless Controller with APs | `show ap debug system-status ap-name <apName>` |  | CLI |
| Wireless Controller with APs | `show ap port status ap-name <apName>` |  | CLI |
| Wireless Controller with APs | `show ap image version` |  | CLI |
| Wireless Controller with APs | `show ap details ap-name <apName>` |  | CLI |
| Wireless Controller with APs | `show ap active` |  | CLI |
| L3 Interfaces | `show vlan status` |  | CLI |
| Wireless clients | `show ap details ap-name <apName>` |  | CLI |
| Wireless clients | `show ap association` |  | CLI |
| Wireless clients | `show wlan summary` |  | CLI |
| Wireless clients | `show wlan <id>` |  | CLI |
| Wireless clients | `show ap active` |  | CLI |
| Vlan | `POST /network-troubleshooting/v1/gateways/<serial-number>/showCommands` | Aruba New Central; the endpoint names no VLAN, so `show vlan` over the showCommands runner supplies the names | API |
| Vlan | `GET /network-monitoring/v1/gateways/<serial-number>/vlans` | Aruba New Central; the endpoint names no VLAN, so `show vlan` over the showCommands runner supplies the names | API |
| Vlan | `show vlan` | Aruba New Central; the endpoint names no VLAN, so `show vlan` over the showCommands runner supplies the names | CLI, API |
| Syslog | `show logging server` |  | CLI |
| Device info | `show telnet` |  | CLI |
| DHCPv4 Relays | `show vlan status` |  | CLI |
| Startup config | `show configuration` |  | CLI |
| Startup config | `show startup-config` |  | CLI |
| Current config | `POST /network-troubleshooting/v1/gateways/<serial-number>/showCommands` |  | API |
| Current config | `show running-config` |  | CLI, API |
| Configuration saved | `show configuration` | Commands are dependend on version | CLI |
| Configuration saved | `show running-config` | Commands are dependend on version | CLI |
| Configuration saved | `show startup-config` | Commands are dependend on version | CLI |
| Device info | `show inventory` |  | CLI |
| Device info | `show slots` |  | CLI |
| DHCPv4 Relays | `show port stats` |  | CLI |
| Device info | `show hostname` |  | CLI |
| Device info | `show version` |  | CLI |
| Device info | `GET /network-monitoring/v1/devices` | the tasker builds the ver from this call; the task sends no request of its own | API |
| ARP | `GET /network-monitoring/v1/gateways/<serial-number>/vlans` | Aruba New Central; the show command runs over the showCommands runner. The VLAN endpoint is the l3Interfaces dependency, read to keep only entries on an interface it emits | API |
| ARP | `POST /network-troubleshooting/v1/gateways/<serial-number>/showCommands` | Aruba New Central; the show command runs over the showCommands runner. The VLAN endpoint is the l3Interfaces dependency, read to keep only entries on an interface it emits | API |
| ARP | `show arp` | Aruba New Central; the show command runs over the showCommands runner. The VLAN endpoint is the l3Interfaces dependency, read to keep only entries on an interface it emits | CLI, API |
| Initial device discovery | `GET /network-monitoring/v1/switches` | the tasker builds the ver from these calls; an MSP login first lists tenants with GET /workspaces/v1/msp-tenants | API |
| Initial device discovery | `GET /network-monitoring/v1/devices` | the tasker builds the ver from these calls; an MSP login first lists tenants with GET /workspaces/v1/msp-tenants | API |
| Initial device discovery | `show version` |  | CLI |
| L2 Interfaces | `show port stats` |  | CLI |
| L3 Interfaces | `show port stats` |  | CLI |
| L3 Interfaces | `show interface <intName>` |  | CLI |
| L3 Interfaces | `show vrrp` |  | CLI |
| L2 Interfaces | `GET /network-monitoring/v1/gateways/<serial-number>/vlans` | physical ports from the API; VLAN interfaces as name-only rows in state unknown; no port-channel interfaces | API |
| L2 Interfaces | `GET /network-monitoring/v1/gateways/<serial-number>/ports` | physical ports from the API; VLAN interfaces as name-only rows in state unknown; no port-channel interfaces | API |
| L2 Interfaces | `show datapath bridge` |  | CLI |
| L2 Interfaces | `show interface loopback` |  | CLI |
| L2 Interfaces | `show interface <intName>` |  | CLI |
| L2 Interfaces | `show vlan status` |  | CLI |
| Disable pagination | `no paging` |  | CLI |
| IP Flow | `show ip-flow-export-profile` |  | CLI |
| FHRP | `show ip interface brief` |  | CLI |
| FHRP | `show vlan status` |  | CLI |
| FHRP | `show port stats` |  | CLI |
| FHRP | `show interface <intName>` |  | CLI |
| FHRP | `show vrrp` |  | CLI |
| DNS resolver | `show ap system-profile` |  | CLI |
| DNS resolver | `show ap system-profile <name>` |  | CLI |
| DHCPv4 Relays | `show interface <int>` |  | CLI |

---

## Supported Tasks

| Category | Task | Status | IPv6 | Notes | Transport |
|----------|------|--------|------|-------|-----------|
| Basic discovery | ARP | ✓ | — | API: Aruba New Central, over the showCommands runner - no API endpoint carries ARP. Only entries on an interface l3Interfaces emits are kept. CX reads all-vrfs, which omits the mgmt VRF, and its allow-list refuses show arp vrf <name>. The AOS-S oobm ARP table is not read. aruba-iap has no L3 interface source, so it stays n/a | CLI, API |
| Basic discovery | Device info | ✓ | — |  | CLI, API |
| Basic discovery | Disable pagination | ✓ | — |  | CLI |
| Basic discovery | FHRP | ✓ | ✗ |  | CLI, API ✗ |
| Basic discovery | Initial device discovery | ✓ | — | API: family, model and version come from the tasker device list | CLI, API |
| Basic discovery | IPv6 Neighbor Discovery | ✓ | ✓ | API: Aruba New Central; only neighbours on a VLAN SVI the gateway VLAN endpoint reports with an IPv4 address - the endpoint exposes no IPv6, so an IPv6-only SVI, a routed port and a loopback are all dropped | CLI ✗, API |
| Basic discovery | L2 Interfaces | ✓ | — | API: switches add VLAN interfaces, loopbacks and per-port MACs from the CLI-over-API runner; gateways add their VLAN interfaces as name-only rows in state unknown; APs are wired ports only | CLI, API |
| Basic discovery | L3 Interfaces | ✓ | ✓ | API: Aruba New Central; SVIs and one primary IPv4 per VLAN from the gateway VLAN endpoint - no running-config source is wired - all in the native VRF | CLI, API |
| Basic discovery | Link aggregations | ✓ | — | API: No bulk LAG source: /gateways/<serial-number>/lag is 404 and the CLI mapper needs one show interface <intName> per port | CLI, API ✗ |
| Basic discovery | MAC | ✓ | — | API: Aruba New Central, over the showCommands runner - no API endpoint carries the MAC table. Only entries on an interface l2Interfaces emits are kept. CX VXLAN entries keep their VTEP but carry no VNI, the vxlan task has no API path. Gateway rows carry no source, and gateway rows on a port-channel or tunnel are not read. AOS-S has no per-VLAN fallback. aruba-iap stays n/a | CLI, API |
| Basic discovery | Neighbors | ✓ | ✗ |  | CLI, API ✗ |
| Basic discovery | Routing table | ✓ | ✗ | API: Aruba New Central gateway, over the showCommands runner. IPv6 is n/i: the runner allows show ipv6 route but its output was never captured. A route line the parser does not recognise is reported, not skipped. CEF entries on an interface l3Interfaces does not emit are dropped and reported | CLI ✗, API |
| Basic discovery | Serial ports | ○ | — |  | — |
| Basic discovery | SN | ✓ | — |  | CLI, API |
| Basic discovery | STP | ○ | — |  | — |
| Basic discovery | Virtual Contexts | ○ | — |  | — |
| Basic discovery | Vlan | ✓ | — | API: Aruba New Central; id, name and operational status on every family, the gateway name coming from `show vlan` rather than the API. `dscr` is on no endpoint, and aruba-iap has no VLAN source at all, so it stays n/a | CLI, API |
| Configuration | Configuration saved | ✓ | — | CLI: Aruba 8.X - not supported, changes must be committed; API: runs over the API but always publishes N/A: deviceConfig/startup does not run over the API | CLI, API ✗ |
| Configuration | Current config | ✓ | — |  | CLI, API |
| Configuration | Startup config | ✓ | — |  | CLI, API ✗ |
| Hardware | Cluster | ○ | — |  | — |
| Hardware | End of Life data | ✓ | — | API: chassis part number only | CLI, API |
| Hardware | Extenders | ○ | — |  | — |
| Hardware | PoE | ○ | — |  | — |
| Hardware | Power supplies & fans | ✗ | — |  | — |
| Hardware | Stacking | ✗ | — |  | — |
| Hardware | Transceivers | ✗ | — |  | — |
| Hardware | VSS | ○ | — |  | — |
| Hybrid discovery | snCheck | ○ | — |  | — |
| Management | DHCPv4 Relays | ✓ | ✗ |  | CLI, API ✗ |
| Management | DHCPv4 Servers | ✗ | ✗ |  | — |
| Management | DNS resolver | ✓ | ✗ |  | CLI, API ✗ |
| Management | IP Flow | ✓ | ✗ |  | CLI, API ✗ |
| Management | License | ○ | — |  | — |
| Management | NTP | ✓ | ✗ |  | CLI, API ✗ |
| Management | Port mirroring | ✗ | — |  | — |
| Management | PTP | ○ | ○ |  | — |
| Management | SNMP | ✓ | ✗ |  | CLI, API ✗ |
| Management | Syslog | ✓ | ✗ |  | CLI, API ✗ |
| Management | Unidirectional Link Detection | ✗ | — |  | — |
| MPLS | Circuit cross-connect | ○ | — |  | — |
| MPLS | MPLS forwarding | ○ | — |  | — |
| MPLS | MPLS LDP | ○ | — |  | — |
| MPLS | RSVP | ○ | — |  | — |
| MPLS | VPLS | ○ | — |  | — |
| MPLS | VPWS | ○ | — |  | — |
| Multicast | IGMP | ✗ | — |  | — |
| Multicast | IGMP Snooping | ✗ | — |  | — |
| Multicast | MAC multicast address table | ○ | — |  | — |
| Multicast | MROUTE | ✗ | — |  | — |
| Multicast | PIM | ✗ | — |  | — |
| Other | Cloud network interfaces | ○ | ○ |  | — |
| Other | PPPoE | ✗ | ✗ |  | — |
| Policy | NAT44 | ✗ | — |  | — |
| QoS | QoS | ✗ | — |  | — |
| Routing | BGP Advertised Routes | ○ | ○ |  | — |
| Routing | Fabric Path | ○ | — |  | — |
| Routing | Policy-based Routing | ○ | ○ |  | — |
| Routing | Route summary | ✗ | ✗ |  | — |
| Routing | Routing policies | ○ | — |  | — |
| Routing | VRF | ○ | — |  | — |
| Routing protocols | BGP neighbors | ○ | ○ |  | — |
| Routing protocols | EIGRP | ○ | ○ |  | — |
| Routing protocols | IS-IS | ○ | ○ |  | — |
| Routing protocols | Lisp | ○ | ○ |  | — |
| Routing protocols | OSPF | ✗ | — |  | — |
| Routing protocols | OSPFv3 | ✗ | ✗ |  | — |
| Routing protocols | RIP | ○ | — |  | — |
| SDN | APIC | ○ | ○ |  | — |
| SDN | Cisco ACI | ○ | ○ |  | — |
| SDN | Virtual machines | ○ | — |  | — |
| SDN | VXLAN | ○ | — |  | — |
| SDWAN | SD-WAN sites | ✗ | — |  | — |
| Security | AAA | ✗ | ✗ |  | — |
| Security | ACL | ✗ | ✗ |  | — |
| Security | DHCPv4 Snooping | ✗ | ✗ |  | — |
| Security | DMVPN | ○ | ○ |  | — |
| Security | Error disabled interfaces | ✗ | — |  | — |
| Security | IPsec | ○ | ○ |  | — |
| Security | LSVPN | ○ | ○ |  | — |
| Security | Prefix lists | ○ | ○ |  | — |
| Security | Secured access ports | ○ | — |  | — |
| Security | Storm control | ○ | — |  | — |
| Security | STP port security | ✗ | — |  | — |
| Security | Virtual servers | ○ | ○ |  | — |
| Security | Zone firewall | ○ | ○ |  | — |
| Wireless | Wireless AP | ✗ | — | HP standalone APs | — |
| Wireless | Wireless clients | ✓ | — |  | CLI, API ✗ |
| Wireless | Wireless Controller with APs | ✓ | — |  | CLI, API ✗ |

---

## All Families from hpe

- [hpe@comware](https://matrix.ipfabric.io/8.2.0/family/200121830)
- **hpe@aruba** *(current)*
- [hpe@arubasw](https://matrix.ipfabric.io/8.2.0/family/200121836)
- [hpe@arubacx](https://matrix.ipfabric.io/8.2.0/family/200121839)
- [hpe@3com](https://matrix.ipfabric.io/8.2.0/family/200121842)
- [hpe@aruba-iap](https://matrix.ipfabric.io/8.2.0/family/200121845)

---

## Legend

- **✓** = Fully Integrated
- **✗** = Not Yet Integrated
- **○** = Not Available
- **🆕** = New in this version
- **CLI** = SSH or Telnet session, **API** = vendor or controller API; in the Transport column, **✗** after one = not yet integrated over it, **—** = not integrated over any transport. A family reached over both may use the API together with CLI or instead of it.

*Generated: 2026-11-22T13:54:33.818Z*
